Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 48 / 93

Troubleshooting

4-8

Part 1603054-02

2015 Nordson Corporation

Meaning/Correction

Fault

Code

Message

Error

Code

306

Internal hardware

failure

E11

Internal DSP fault in gun control card.

1. Turn off the power to the system.
2. Unplug the cable from the back of the gun.
3. Turn on the power to the system.

If the fault code changes to E7 (open circuit), the card is

working correctly. Check the gun multiplier.
If the fault code remains at E11, replace the gun control card.

308

Gun not detected

E16

Gun not connected to system. Check the gun cable

connections and make sure the gun card is seated securely into

the backplane. This is a normal indication if power to cards is

removed, such as when the booth exhaust fan is shut off.

531

System heartbeat

lost

−

Check circuit board connections.

532

5/24 volt power

−

Check circuit board connections.

533

Error writing to

internal EEPROM

−

Hardware error. Replace card.

534

Error reading to

internal EEPROM

−

Hardware error. Replace card.

535

Node address

changed from last

power up

−

Saved address does not match current address. Address

switches were changed. Informational message only.

536

Internal database

version changed

−

resetting to

defaults

−

An update to the database was detected and the current data is

no longer valid. Informational message only, operation should

not be affected.

537

Preset out of

range

−

The preset sent to the remote device was out of range. Check

preset settings and reset as required.

538

Trigger ON

message received

−

controller in

lockout

−

The card was commanded to trigger but the system is locked

out. Trigger ON commands will be ignored until the system is

returned to the Run state.

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды