Nordson Encore HD iControl System Скачать руководство пользователя страница 18

Страница: 18 / 93

System Overview

2-6

Part 1603054-02

2015 Nordson Corporation

Gun Control Cards

Each gun control card in the card cage provides electrostatic controls for

two Encore HD automatic powder spray guns. The cards provide AC power

to the voltage multipliers (power supplies) in the automatic guns, and

process feedback from the guns for display on the operator interface.

Encore HD manual spray guns are controlled by the manual gun controllers.

Gun Pump Control

The iControl console and the manual gun controllers control the HDLV

powder pumps through the CAN network. In the pump cabinet, one pump

control card controls two pumps.

Refer to the HDLV pump and pump panel manuals for wiring diagrams,

parts lists, and other information.

Specifications

General

Electrical Requirements

Input

Unswitched: (PC) 100

−

230 Vac, 50/60 Hz, 1



, 120 VA max.

Switched: 100

−

230 Vac, 50/60 Hz, 1



, 480VA max.

Conveyor Interlock and Remote Lockout: 120/230 Vac, 50/60

Hz, 1



, 6 mA

Alarm Relay contact rating: 120/230 Vac, 1



, 6 A

Output (to spray gun)



19 Vac, 1 A

NOTE:

The iControl system must be interlocked with the fire detection system so that the spray guns are

shut off if a fire is detected inside the spray booth.

ANSI/ISA S82.02.01

Pollution Degree

Installation (Overvoltage)

Category II

Environmental

Operating Temperature

−

104

F (0

−

Operating Humidity

−

95%, non-condensing

Hazardous Location Rating

North America: Class

Division 2, Groups F & G

European Union: Ex

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Бренды по названию

Популярные бренды