Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 72 / 93

Troubleshooting

4-32

Part 1603054-02

2015 Nordson Corporation

Calibration with a Mouse

(contd)

Use this procedure to recalibrate the touch screen if you cannot touch the

CAL button or the buttons on the iControl screens, or if you install a

program card previously used in another iControl console.

NOTE:

You must shut off console power before connecting or

disconnecting a mouse or keyboard from the iControl PC.
1. Turn off console power.
2. Open the iControl cabinet door and connect a mouse with a PS2

connector to the MOUSE port on left side of the iControl PC.

3. Turn on power and allow the operating system to load. The CAL button

is displayed on the touch screen before the iControl software loads.

4. Use the mouse to move the cursor to the CAL button and click on it.

The touch screen calibration procedure will start.

NOTE:

If you miss the CAL button, allow the iControl software to load,

then, if possible, open the System Configuration screen and touch the

Program Shutdown button. When the operating system shutdown

prompt appears on the screen, touch the Cancel button, then touch the

CAL button. If you cannot touch any buttons on the screen, then you

will have to cycle console power and try again.

5. When the calibration procedure starts, USE YOUR FINGER, NOT THE

MOUSE, to touch the calibration targets, following the instructions on the

screen carefully. When you have completed the calibration procedure,

touch the iControl button to start the iControl software.

6. Test the touch screen calibration, then perform a program shutdown,

turn off console power, and disconnect the mouse.

No Touch Screen Display

Check the following:

Check the power LED on the front bezel below the screen. If LED is not

lit then PC is not powered up.

Make sure console power switch is on.

Open the console door and make sure the PC power switch is on.

Have an electrician check these:

Console fuses on the DIN rail, at the incoming power terminals.

Unswitched power connections to the fuse blocks.

Power supply to the console.

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды