Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 65 / 93

Troubleshooting

4-25

Part 1603054-02

2015 Nordson Corporation

Correction

Message

Error

Code

2007

2008

Up or

Down

End-of-Travel Limit fault

Auto mode is selected and the reciprocator has engaged the

forward (upper) or reverse (lower) end-of-travel limit sensor.
Select Manual mode and move the reciprocator off the limit,

then re-select Auto mode.
Check the configured soft top and bottom limits. Make sure

they do not allow travel to the limit sensors.
Adjust the configured reciprocator Turn-Around Offset

(Nordson CSR only) to ensure that the limit sensors are not

engaged.
Check reciprocator encoder wiring. If signals are switched the

position tracking will be reversed. Typically only seen on initial

startup or if encoder is replaced.
Reciprocator encoder has failed. Refer to Encoder Failure

fault.
Gun carriage has fallen to the down limit as a result of a

mechanical failure.
Check belts, pulleys, bearings, etc. for proper operation.

Refer to reciprocator manual.
This fault must be reset from the iControl Alarm screen.
Gun carriage has slowly drifted or was moved to the top or

bottom of stroke.
Incorrect counterweight to neutralize the weight of the guns

and gun carriage. Refer to reciprocator manual.
This fault must be reset from the iControl Alarm screen.

2101

Part size less than minimum

Default or preset settings define a stroke length less than the

minimum 4 in.
Change default or preset settings, or if parts are small

consider turning off reciprocators for batch.

2102

Lead gun not defined

−

using

gun 1

Lead gun number not entered in reciprocator configuration.
Enter number for lead gun in reciprocator configuration.

2103

Trail gun not defined

−

using

gun 1

Trail gun number not entered in reciprocator configuration.
Enter number for trail gun in reciprocator configuration.

2104

Trail gun less than lead

−

trail = lead

Lead and trail gun numbers not entered correctly in

reciprocator configuration.
Correct gun number entries in reciprocator configuration.

Lead gun number must be lower than trail gun number.

2105

Pattern width not set

−

using

12 inches

No value for pattern width entered in reciprocator

configuration.
Enter value for pattern width in reciprocator configuration.

2106

Vertical scanner not

configured

−

reciprocator

mode 1 invalid

Reciprocator set for variable stroke mode, no part size data

available.
A part size, as seen by a vertical scanner or customer PLC, is

required for variable mode. If no part size data is available,

set reciprocator to a fixed mode.

Continued...

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды