Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 47 / 93

Troubleshooting

4-7

Part 1603054-02

2015 Nordson Corporation

Gun Card Troubleshooting

Refer to Figure 4-1 and Tables 4-3 and 4-4. Use the fault codes on the Gun

Control screens, the fault messages on the Alarm screen, and the LEDs on

the gun control cards to diagnose problems with the gun control cards.

Gun Card Error Codes and Fault Codes

These faults, except for E16, will activate the alarm relay.

Table 4-3 Gun Card Error and Fault Codes

Error

Code

Message

Fault

Code

Meaning/Correction

301

Micro-Amp fault

detected

−

Micro-amp value out of range.

302

Over-current fault

detected

E15

Over-current detected. Clear the fault, unplug the cable from

the gun and trigger the gun.

If the fault changes to E7, check the resistance of the
multiplier as described in the gun manual.

If the fault code stays E15, check the continuity of the cable

as described in the gun manual.

303

Feedback fault

detected

Micro-amp feedback not detected. Check the gun current with

no parts in front of the gun. If the current is 105



A, check for a

short circuit of the current feedback wires in the gun cable:
Unplug the cable from the gun and trigger the gun.

If the fault stays E3, replace the cable.

If the fault changes to E7, check the resistance of the
multiplier as described in the gun manual.

304

Open circuit

detected

Gun cable or multiplier open circuit. If the current display is 1



A or less, check the multiplier cable and electrode assembly

for loose connections.

If the connections are secure, check the multiplier with an
ohmmeter as described in the gun manual.

If the multiplier reading is acceptable, check for a defective

cable as described in the gun manual.

305

Short circuit

detected

Gun cable or multiplier short circuit. Unplug the cable from the

gun and trigger the gun.

If the fault changes to E7, check the resistance of the
multiplier as described in the gun manual.

If the fault code stays E8, check the continuity of the cable

as described in the gun manual.

Continued...

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды