manualshive.com logo in svg

Nordson Encore HD iControl System, Руководство по оборудованию

Поделиться
Скачать
Nordson Encore HD iControl System Скачать руководство пользователя страница 45

Troubleshooting

4-5

Part 1603054-02

E

 2015 Nordson Corporation

Refer to

Page

Description

Message Text

Code

1008

Reverse End of Travel Limit

The machine is at the reverse end of travel

limit.

4-18

1112

Positioner not in ready state

for Color Change

The positioner has not reached the proper

location for color change.

4-18

200x, 210x

Reciprocator

2001

E-Stop Open

The E-Stop circuit is open.

4-23

2002

Encoder failure

The encoder is not responding when motion is

commanded or is responding with defective

signals.

4-23

2003

Motor Protector

The motor protector is open.

4-24

2004

Motion Controller

The motion controller indicates a failure.

4-24

2005

Forward Contactor

The forward contactor did not engage.

4-24

2006

Reverse Contactor

The reverse contactor did not engage.

4-24

2007

Forward End of Travel Limit

The machine is at the forward end of travel

limit.

4-25

2008

Reverse End of Travel Limit

The machine is at the reverse end of travel

limit.

4-25

2101

Part size less than minimum

The part detected is too small. The

reciprocator will attempt to stroke at the

minimum length.

4-25

2102

Lead gun not defined 

−

 using

gun 1

The lead gun on the reciprocator is not

defined.

4-25

2103

Trail gun not defined 

−

 using

gun 1

The trailing gun on the reciprocator is not

defined.

4-25

2104

Trail gun less than lead 

−

 

trail = lead

The trailing gun number is less than the lead

gun number.

4-25

2105

Pattern width not set 

−

 using

12 inches (305 mm)

The pattern width has not been set using

default.

4-25

2106

Vertical scanner not

configured 

−

 recip mode 1

invalid

A vertical scanner is required for variable

stroke operation.

4-25

2107

Speed calculated less than

minimum

The speed of the reciprocator is less than the

minimum value allowed.

4-26

2108

Speed calculated greater

than maximum

The speed of the reciprocator is greater than

the maximum value allowed.

4-26

2113

Reciprocator not in ready

state for Color Change

The reciprocator is not in the proper position

for color change.

4-26

300x

Watchdog

3100

Positioner Watchdog fault

The remote Ethernet device did not respond

with a watchdog signal in 1 second.

4-18

3200

Reciprocator Watchdog fault

The remote Ethernet device did not respond

with a watchdog signal in 1 second.

4-26

Continued...

Obsolete 

Содержание Encore HD iControl System






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды