Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 37 / 93

Installation

3-15

Part 1603054-02

2015 Nordson Corporation

Gun Cable and Feed Tubing Connections

See Figure 3-9. Connect the automatic gun cables to the receptacles on

the bottom rear panel of the iControl console. Connect gun 1 cable to

receptacle 1, gun 2 cable to receptacle 2, and so on.

Connect the 8-mm powder feed tubing from the spray guns to the HDLV

pump outlet fittings as described in the pump panel manual.

Connect the pattern air tubing from the spray guns to the pump panel outlet

fittings next to the pumps.

Odd Number of Guns

iControl systems are sold configured for an even number of guns. Each

gun controller card in the console controls two guns. If you configure the

system for an odd number of guns, the fault LED on the card with only one

gun connected will light.

NOTE:

The unused gun must be the highest even-number gun. For

example, if you have an 8-gun system, then number 8 must be the unused

gun. The gun card receptacles are labeled on the circuit boards as A (odd

number gun) and B (even number gun).

Included in the bag with the console keys is a seal and jumper. The jumper

will disable the gun not detected fault LED on the gun card.

Cap the unused cable receptacle with the bulkhead seal, then open the

console door and unplug the receptacle harness from the gun card. Install

the jumper in the card receptacle.

Refer to the Parts section for seal and jumper part numbers.

Bulkhead

Seal

Jumper

Install in #8 Card

Receptacle

Gun Card

Harnesses

Gun Cables

Receptacle #8

Figure 3-9

Seal and Jumper Installation

−

Example Showing 8 Gun System with 7 Guns

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды