Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 26 / 93

Installation

3-4

Part 1603054-02

2015 Nordson Corporation

iControl Console CAN Address and Termination Settings

The backplane address dipswitches are set at the factory:

1. Network terminator switch SW1-3 is set to CONTINUOUS for both

backplanes.

2. Network address switches SW1-1 and 2 are set to Guns 1

−

16 for the

lower backplane and to 17

−

32 for the upper backplane (if used).

SW1

Open

Rocker switch

Closed

(top in)

Open

(bottom in)

Slide switch

Closed

(on)

Open

SW1

Open

Upper Backplane

Guns 17

−

Lower Backplane

Guns 1

−

SW1

−

SW1

−

Closed

Guns 1

−

Closed

Open

Gun 17

−

SW1

−

Closed: End

Open:

Continuous

Figure 3-2

CAN Network Connections, Console Addresses, and Termination

Manual Gun Controller Addresses

The manual gun controller addresses are set through software. Each

controller must have a unique address. Up to four manual guns can be

included in a system. Refer to the gun controller manual for instructions.

Manual Gun Controller Termination

Manual gun controllers are shipped with their CAN termination switch set to

ON. For each manual gun controller in the system:

1. Open the controller enclosure and locate SW1 on the controller interface

board.

2. Set the TERM switch on SW1 to OFF.

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды