Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 35 / 93

Installation

3-13

Part 1603054-02

2015 Nordson Corporation

NOTE:

If using a single horizontal scanner, the controller must be

programmed to ignore the conveyor. This requires software from the

scanner manufacturer, a laptop running Windows, and a serial cable to

connect the laptop to the scanner controller in the junction box.

BSCE

−

BSCR

−

BSCE

−

BSCR

−

Dual Positioner Scanner Configuration

PEJB

Positioner

Scanner J-Box

SCNR1

Ethernet

BSCE

BSCR

PEJB

Positioner

Scanner J-Box

SCNR1

Ethernet

Single Positioner Scanner Configuration

Figure 3-7

In/Out Positioner and Reciprocator Analog Scanner Connections

Customer-Supplied Part ID System Connections

Refer to Table 3-2. Use the Part ID terminals on the PEJB to connect a

customer-supplied part ID system to the iControl console. The 8 inputs are

used based on the settings made in the Photoeye Configuration screen.

Refer to the

iControl Operator Interface

manual for configuration

instructions.

Ethernet Network/Gun Mover Control

The Ethernet network allows the iControl system to communicate with the

gun mover PLCs and the analog scanner controllers through a network

switch. The PLCs control the Variable Frequency Drives (VFDs) that power

and control the gun mover motors according to the settings made in the

iControl software.

Oscillators are not controlled by the iControl software. The PLCs control

their motion during color changes only.

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды