Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 21 / 93

System Overview

2-9

Part 1603054-02

2015 Nordson Corporation

Approved Program and User Data Cards

NOTE:

Refer to the Parts section for the Nordson part number for the

Compact Flash cards shipped with the system.

CompactFlash card capacity: 512 Mb minimum

−

Type I CompactFlash only.

NOTE:

Retail

CompactFlash refers to cards available at camera, computer,

and electronic retail shops. Retail flash has a rating of 30,000 to 600,000

write cycles at a maximum of 75

C (167

F) and may experience a shorter

overall life.

Industrial

CompactFlash refers to rated cards only available through an

electronics parts supplier and online sources that sell CompactFlash with an

industrial temperature rating for use in Embedded Systems. Industrial flash

has a rating of 2,000,000 write cycles and an increased temperature range

to 85

C (185

F).

Cards that have been validated:

SanDisk

−

retail to 2 GB, industrial to 1 GB

Toshiba

−

retail to 2 GB

PNY

−

retail to 2 GB

Dane-Elec

−

retail 512 MB

Kingston Technology

−

retail to 4 GB

Smart Modular Technologies

−

industrial to 1 GB

SMC Numonyx

−

industrial to 1 GB

Silicon Systems

−

industrial 512 MB

Transcend

−

industrial 512 MB

SanDisk

−

industrial 4 GB and larger (must be used in pairs)

NOTE:

With the industrial Sandisk card, the system will not boot completely

or in a timely manner when either the data or program flash card differs in

size.

Incompatible cards with iControl:

LEXAR

−

any

Type II

−

any (Type II CompactFlash cards are larger and will not fit into

the card holder.

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды