manualshive.com logo in svg

Nordson Encore HD iControl System, Руководство по оборудованию

Поделиться
Скачать
Nordson Encore HD iControl System Скачать руководство пользователя страница 34

Installation

3-12

Part 1603054-02

E

 2015 Nordson Corporation

Single Zone Scanner

Dual Zone Scanners

Part ID and Zone Scanners

SCNR1

SCNR1

SCNR2

PEJB

Part ID Scanner

or Customer

Part ID System

Zone Scanner

Part Travel

Figure 3-6

Zone and Part ID Scanner Cable Connections

Analog Scanner Connections 

See Figure 3-7.  The in/out positioner scanner junction box is typically

located on the same stand as the photoeye junction box.  One or two

scanners can be used to detect the width of the parts.  The scanners must

be mounted with the cable ends oriented as shown.  If using dual scanners,

mount them so that they do not see the conveyor.  Connect the positioner

scanner cables (BSCE, BSCR) from the junction box to the scanners as

shown.

If the system also has reciprocators, then analog scanners are used to

detect the part height and top and bottom edges.  Mount the scanners with

the cable ends down and connect the cables (SCNR1) from the PEJB to the

scanners.

Maximum Analog Scanner Separation:

6 meters (20 ft) if scanner is less than 1.22 meters (4 ft) long

4.6 meters (15 ft) if scanner is greater than 1.22 meters (4 ft) long.

Obsolete 

Содержание Encore HD iControl System






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды