Nikon NPL-632 Скачать руководство пользователя

Страница: 3 / 206

Field Station NPL-632 Instruction Manual

iii

Contents

Introduction .   .  .   . .   .  .   . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . .   . .   .  . . .   .  .  12
Laser Safety.   .  .   . .   .  .   . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . .   . .   .  . . .   .  .  12
Warnings and Cautions .  .   . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . . . .   .  . . .   .  .  13

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Welcome .  .   .  .   . .   .  .   . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . .   . .   .  . . .   .  .   2
Parts of the Instrument  .  .   . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . . . .   .  . . .   .  .   3
Maintenance    .  .   . .   .  .   . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . . .  .   .  .   . .   .  .   5

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpacking and Packing the Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Charging the Battery Pack   . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . . . .   .  . . .   .  .   8
Detaching and Re-Attaching the Battery Pack. . .  .   . . . .   . . . .   . . . .   . . . .   .  . . .   . .  10
Using the CompactFlash (CF) Card . . .  .   . . .  .   . . . .   . . . .   . . . .   . . . .   .  . .  .   . .  11

Inserting a CF card into the card slot . . . . . . . . . . . . . . . . . . . . . . . 12
Removing a CF card from the card slot . . . . . . . . . . . . . . . . . . . . . . 13

Using the USB Memory Stick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Inserting the USB memory stick into the connector slot . . . . . . . . . . . . . . . . 14
Transferring files from the instrument to an office computer using USB . . . . . . . . . 14

Measurement with a prism . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Measurement in Reflectorless mode . . . . . . . . . . . . . . . . . . . . . . . 19

Preparing the Reflector Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setting Up the Prism Reflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Adjusting the height of the tribrach adapter . .    .  .   .  .   . .    .  .    . .   . .   .  .   .  .   . .    . 22
Changing the direction of the prism     . .    . .   .  .   .  .   . .    .  .    . .   . .   .  .   .  .   . .    . 23
Setting the prism constant   . .    .  .    . .   . .   .  .   .  .   . .    .  .    . .   . .   .  .   .  .   .  .    . 23
Setting the position of the target plate  . .   . .   .  .   .  .   . .    .  .    . .   . .   .  .   .  .   . .      . 24

Carrying the Instrument Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Face-1/Face-2 Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Turning the Instrument On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Turning on the instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Turning off the instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Selecting a Language    .  .   . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . . . .   .  . . .   .  .  29
Changing Regional Configuration Pre-sets .   . . .  .   . . . .   . . . .   . . . .   . . . .   .  . . .   . .  30
Display and Key Functions  . .   .  .   . . .  .   . . .  .   . . . .   . . . .   . . . .   . . . .   .  . . .   .  .  31

Status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Содержание NPL-632















































































































































































































Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды

Nikon NPL-632, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды