Nikon NPL-632 Скачать руководство пользователя | Manualshive

Страница: 23 / 206

background image

Field Station NPL-632 Instruction Manual

9

Preparation

2

C

WARNING –

Although the battery pack (P/N BC-80) has an auto-reset circuit breaker, you

should take care not to short circuit the contacts. Short circuits can cause the battery pack to
catch fire or burn you.

C

WARNING –

Never burn or heat the battery. Doing so may cause the battery to leak or rupture.

A leaking or ruptured battery can cause serious injury.

C

WARNING –

Before storing the battery pack or battery charger, cover the contact points with

insulation tape. If you do not cover the contact points, the battery pack or charger may short
circuit, causing fire, burns, or damage to the instrument.

Important notes

•

Charge the battery pack indoors when the ambient temperature is between
10 °C and 40 °C (between 50 °F and 104 °F). If you try to charge the battery
when the ambient temperature is outside this range, the protective circuit will
activate and prevent it from being charged normally.

•

After charging the battery pack, do not recharge it until it has been fully
discharged. Recharging a fully charged battery pack lowers its performance.

•

To prevent malfunction, keep the charging plug clean.

•

If the charger indicator LED2 blinks orange and green after charging is started,
there may be a problem in the battery pack. Do NOT use or charge the battery
pack any further. Please contact your dealer.

•

If the ambient temperature drops below 10 °C (50 °F) while the battery pack is
charging, charging stops. When the ambient temperature rises above 10 °C
(50 °F), charging resumes.

•

If both the charger indicators LED1 and LED2 remain orange for more than
three hours while the ambient temperature is in the normal range (10 °C
through 40 °C or 50 °F through 104 °F), there may be a problem with the
battery pack. Do NOT use or charge the battery pack any further. Please
contact your dealer.

•

During the charge, the battery pack and charger will become warm. This is
normal.

•

If the battery pack is used at temperatures below -20 °C (-4 °F), the battery
capacity will be reduced and result in less operation time than if the battery
pack is used at room temperature.

•

If a battery pack is not used for a long period, it can never be charged to its full
capacity again.

«
...
21
22
23
24
25
...
»

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

Бренд: rainforest Страницы: 2

Бренд: Yamaha Страницы: 3

Бренд: 3B6 Страницы: 30

Бренд: BANTE inststruments Страницы: 15

Бренд: 3Bays Страницы: 21

Vigilant ELM Series

Бренд: Eagle Eye Power Solutions Страницы: 9

Бренд: Campbell Страницы: 22

Бренд: Campbell Страницы: 32

Бренд: Campbell Страницы: 40

CR3000 Micrologger

Бренд: Campbell Страницы: 12

Бренд: R.M. Young Страницы: 8

Бренд: Campbell Страницы: 21

Бренд: National Instruments Страницы: 18

Бренд: SAGEMCOM Страницы: 33

Бренд: YOKOGAWA Страницы: 53

Бренд: Hilti Страницы: 31

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды