Nikon NPL-632 Скачать руководство пользователя

Страница: 88 / 206

Applications

Field Station NPL-632 Instruction Manual

The observation screen for the first stake (from
the instrument) appears.

Sight the prism and then press

[MSR1]

[MSR2]

Use

[^]

[v]

to change the guide point. You can

calculate and guide up to double the number of
the stakes.

To record the point as an SO record, press

[ENT]

RefLine S-O

This function allows you to stake out a point based on the Sta, O/S, and dZ to a
specified line.

Press

[4]

or select

RefLine S-O

in the Stakeout menu.

Enter the first point (P1) of the line.

For example, if you measure to the end point at 100 m from the instrument and set the span total to 2, the
following four points are calculated and can be staked:

<1/2>

<2/2>

<3/2>

<4/2>

50 m

100 m

150 m

200 m

Содержание NPL-632















































































































































































































Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды

Nikon NPL-632, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды