Nikon NPL-632 Скачать руководство пользователя | Manualshive

Страница: 12 / 206

background image

Safety

14

Field Station NPL-632 Instruction Manual

C

WARNING –

Although the battery pack (P/N BC-80) has an auto-reset circuit breaker, you

should take care not to short circuit the contacts. Short circuits can cause the battery pack to
catch fire or burn you.

C

WARNING –

Never burn or heat the battery. Doing so may cause the battery to leak or rupture.

A leaking or ruptured battery can cause serious injury.

C

WARNING –

Before storing the battery pack or battery charger, cover the contact points with

insulation tape. If you do not cover the contact points, the battery pack or charger may short
circuit, causing fire, burns, or damage to the instrument.

Cautions

Before using the instrument, read the following cautions and follow the instructions
that they provide:

C

CAUTION – Use of controls, adjustments, or performance of procedures other than those
specified herein may result in hazardous radiation exposure.

C

CAUTION – The tips of the tripod ferrules are very sharp. When handling or carrying the tripod,
take care to avoid injuring yourself on the ferrules.

C

CAUTION – Although a Class 1 laser is regarded as safe under normal operating conditions, it
is recommended that you cap the objective when the instrument is not in use in order to avoid
laser emissions. Do NOT look into the laser.

C

CAUTION – Before carrying the tripod or the instrument in the carrying case, check the
shoulder strap and its clasp. If the strap is damaged or the clasp is not securely fastened, the
carrying case may fall, causing personal injury or instrument damage.

C

CAUTION – Before setting up the tripod, make sure that no-one’s hands or feet are underneath
it. When the legs of the tripod are being driven into the ground, they could pierce hands or feet.

C

CAUTION – After mounting the instrument on the tripod, securely fasten the thumb screws on
the tripod legs. If the thumb screws are not securely fastened, the tripod may collapse, causing
personal injury or instrument damage.

C

CAUTION – After mounting the instrument on the tripod, securely fasten the clamp screw on
the tripod. If the clamp screw is not securely fastened, the instrument may fall off the tripod,
causing personal injury or instrument damage.

«
...
10
11
12
13
14
...
»

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

Бренд: WAGER Страницы: 22

Бренд: Eaton Страницы: 43

Бренд: Danfoss Страницы: 6

Бренд: Unico Страницы: 10

Бренд: LaMotte Страницы: 2

Бренд: Lampa Страницы: 12

Бренд: UEi Страницы: 5

Stream Line Pro

Бренд: Halo Photonics Страницы: 45

Stubby LED-1500

Бренд: Dive Perfect Страницы: 4

Бренд: Dakota Digital Страницы: 34

Бренд: Value Страницы: 20

Бренд: Roland Страницы: 224

Бренд: EIJKELKAMP Страницы: 11

Бренд: Panametrics Страницы: 224

Бренд: Hanna Instruments Страницы: 2

Бренд: R&S Страницы: 23

Бренд: Kimo Страницы: 80

Бренд: Vmetro Страницы: 186

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды