manualshive.com logo in svg

Nikon NPL-632, Инструкция по эксплуатации

Nikon NPL-632 - профессиональный нивелир с высокой точностью и надежностью. Инструкция по эксплуатации в формате PDF доступна для бесплатного скачивания на manualshive.com. Получите подробное руководство по эксплуатации и настройке прибора для оптимальных результатов работы.

Поделиться
Скачать
background image

Contact Information

Trimble Navigation Limited

Engineering and Construction Division

5475 Kellenburger Road

Dayton, Ohio 45424-1099

USA
800-538-7800 (toll free in USA)

+1-937-245-5600 Phone

+1-937-233-9004 Fax

www.trimble.com

Copyright and Trademarks

© 2006, Nikon-Trimble Co. Limited. All rights reserved.
Microsoft, Windows, and ActiveSync are either registered trademarks 

or trademarks of Microsoft Corporation in the United States and/or 

other countries. 
All trademarks are the property of their respective owners.
It is prohibited to alter this manual in part or whole without express 

permission.
The contents of this manual are subject to change without notice. 

Although every effort has been made to ensure the accuracy of this 

manual, please contact your dealer if you find anything in it that is 

incorrect or unclear.

Release Notice

This is the May 2006 release (revision A) of the

 Field Station NPL-632 

Instruction Manual

. It applies to software release version 1.10 for the 

field station NPL-632.

Notices
USA

FCC 15B Class B satisfied.
This equipment has been tested and found to comply with the limits for 

a Class B personal computer and peripherals, pursuant to Part 15 of the 

FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This 

equipment generates, uses and can radiate radio frequency energy and, 

if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and 

on, the user is encouraged to try to correct the interference by one or 

more of the following measures:
– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that 

to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

C

Warning – 

This equipment has been certified to 

comply with the limits for a Class B personal computer 
and peripherals, pursuant to Subpart B of Part 15 of 
FCC Rules. Only peripherals (computer input/output 
devices, terminals, printers, etc.) certified to comply 
with the Class B limits may be attached to this 
equipment. Operation with non-certified personal 
computer and/or peripherals is likely to result in 
interference to radio and TV reception. The connection 
of a non-shielded equipment interface cable to this 
equipment will invalidate the FCC Certification of this 
device and may cause interference levels which exceed 
the limits established by the FCC for this equipment.

You are cautioned that changes or modifications not 
expressly approved by the party responsible for 
compliance could void your authority to operate the 
equipment.

European Union

EU EMC Directive satisfied. 

Canada

This Class B digital apparatus meets all requirements of the Canadian 

Interference-Causing Equipment Regulations.
Cet appareil numérique de la Class B respecte toutes les exigences du 

Règlement sur le matériel brouilleur du Canada.

Taiwan

Battery recycling requirements

The product contains a removable battery. Taiwanese 

regulations require that waste batteries are recycled.

Notice to Our European Union Customers

For product recycling instructions and more information, 

please go to:
 

www.trimble.com/environment/summary.html

Recycling in Europe

To recycle Trimble WEEE, 

call: +31 497 53 2430, 

and ask for the “WEEE associate,” 

or mail a request for recycling instructions to:
Trimble Europe BV

c/o Menlo Worldwide Logistics

Meerheide 45

5521 DZ Eersel, NL

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

Cannon CAV 4.2 Operation Manual preview
CAV 4.2
Бренд: Cannon Страницы: 64
Cannon CAV 4.1 Operation Manual preview
CAV 4.1
Бренд: Cannon Страницы: 73
Radio Shack TRS-80 Owner'S Manual preview
TRS-80
Бренд: Radio Shack Страницы: 44
Radiodetection RD8100 Quick Locating Manual preview
RD8100
Бренд: Radiodetection Страницы: 2
OBD VD10 User Manual preview
VD10
Бренд: OBD Страницы: 5
Ecolab LMIT09/S209 Short Operating Instructions preview
LMIT09/S209
Бренд: Ecolab Страницы: 95
Dewetron DEWE2-A4L Technical Reference Manual preview
DEWE2-A4L
Бренд: Dewetron Страницы: 24
Environmental Express 99561-84 Instruction Manual preview
99561-84
Бренд: Environmental Express Страницы: 40
PASCO WA-7428 Product Manual preview
WA-7428
Бренд: PASCO Страницы: 4
RADWAG MA 3Y User Manual preview
MA 3Y
Бренд: RADWAG Страницы: 176
Bartec TECH550PRO User Manual preview
TECH550PRO
Бренд: Bartec Страницы: 38
Fluke 55XXA/COIL 50 Instructions Manual preview
55XXA/COIL 50
Бренд: Fluke Страницы: 6
D-tect Systems MiniRad-DX Installation And Operating Instructions Manual preview
MiniRad-DX
Бренд: D-tect Systems Страницы: 28
LaserLiner DistanceMaster Compact Operating Instructions Manual preview
DistanceMaster Compact
Бренд: LaserLiner Страницы: 14
inbody 370S User Manual preview
370S
Бренд: inbody Страницы: 36
Extech Instruments HD755 User Manual preview
HD755
Бренд: Extech Instruments Страницы: 8
GRAVITY TRAVELER 3D ARM Quick Start Manual preview
TRAVELER 3D ARM
Бренд: GRAVITY Страницы: 2
Hanna Instruments HI 720 Instruction Manual preview
HI 720
Бренд: Hanna Instruments Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды