Nikon NPL-632 Скачать руководство пользователя

Страница: 137 / 206

Field Station NPL-632 Instruction Manual

123

Menu Key

When you input a Stn-XYZ by Base-XYZ function, the
recorded station appears as a comment record.

SY records

When you complete a station setup, an SY record is
stored. This record contains the Temperature, Pressure,
and Prism Constant values.

RM records

When you record measurements in RDM (Cont) or
RDM (Rad), they are labeled as RM records.

Each RM record consists of two screens.

Press

[DSP]

to switch between the first screen (showing

From, To, rHD, and rVD) and the second screen
(showing rAZ, rSD, rV%, and rGD).

When you download data in Nikon RAW format, RM
records are output as comment (CO) records.

AR records

An AR record stores an area and perimeter calculation.

When you download data in Nikon RAW format, AR
records are output as comment (CO) records.

View coordinate data

When you press

[2]

or select

XYZ data

in the Data

menu, coordinate data appears in a list, with the newest
record at the bottom of the screen. Use

[^]

[v]

to scroll

through the records. Use

[<]

[>]

to move up or down

one page.

Содержание NPL-632















































































































































































































Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды

Nikon NPL-632, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды