Nikon NPL-632 Скачать руководство пользователя | Manualshive

Страница: 48 / 206

background image

3

Getting Started

34

Field Station NPL-632 Instruction Manual

Input mode indicator

The Input mode indicator only appears when you are entering points or coordinates. It
shows the data input mode:

Lumi-guide indicator

The Lumi-guide indicator shows the status of the Lumi-guide tracking light.

EDM measurement status

When you are taking measurements, the EDM measurement status shows the mode
that is being used.

When you display observation data, the EDM measurement status shows the mode
that was used when the data was collected.

Battery indicator

The battery indicator shows the battery voltage level:

If the battery level is critically low, the following
message appears:

Input mode is numeric. Press a key on the number pad to enter the number printed on the
key.
Input mode is alphabetic. Press a key on the number pad to enter the first letter printed
beside the key. Press the key repeatedly to cycle through all the letters assigned to that
key.
For example, to enter the letter O in alphabetic mode, press

[5]

three times.

Lumi-guide tracking light is on.

If there is no icon, the Lumi-guide tracking light is turned off.

Reflectorless mode

If there is no icon, Prism mode is being used.

Level 4 (Full)

Level 3

Level 2

Level 1

Battery low

«
...
46
47
48
49
50
...
»

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

Бренд: C-LOGIC Страницы: 2

Бренд: Jennov Страницы: 50

Бренд: Han Seung Страницы: 2

Бренд: Parkside Страницы: 94

Бренд: WATERGUARD Страницы: 2

Бренд: Valcom Страницы: 1

Бренд: LumaSense Страницы: 23

Бренд: SKF Страницы: 12

Бренд: IFM Страницы: 38

Бренд: Leica Страницы: 2

DIGIMET E30 Preset

Бренд: MATO Страницы: 20

Бренд: Hanna Instruments Страницы: 28

Бренд: Omega Страницы: 4

Бренд: Kane Страницы: 36

Бренд: Veeder-Root Страницы: 12

PA 900 Musikant

Бренд: Korg Страницы: 20

Бренд: Hanna Instruments Страницы: 84

Бренд: KAM Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды