Nikon NPL-632 Скачать руководство пользователя | Manualshive

Страница: 27 / 206

background image

Field Station NPL-632 Instruction Manual

13

Preparation

2

C

CAUTION – If you force the cover closed when the protrusion on the knob cover is set to the
LOCK (horizontal) position, you may damage the cover.

4.

Rotate the knob counter-clockwise until the protrusion on the knob in set to the
LOCK position.

Note –

To ensure that the cover is firmly locked, the cover remains slightly open if you

do not rotate the knob correctly so that the protrusion points to the LOCK position.
Make sure that the cover is firmly closed.

Removing a CF card from the card slot

1.

Open the card slot cover by rotating the
knob clockwise until the protrusion on the
knob is set to the OPEN position.

2.

To remove the CF card, press the eject
button.

Using the USB Memory Stick

C

CAUTION – Before you open the card slot cover, wipe off all moisture. If you open the cap or
cover while they are wet, it may result in malfunction.

C

CAUTION – Nikon recommends that you format the USB memory stick on your office computer
before you use it for the first time.

C

CAUTION – While the system is writing data to the USB memory or deleting data in the USB
memory, do NOT carry out the following actions as this may result in data corruption or card
malfunction:
- Remove the USB memory stick
- Remove the battery pack
- Turn off the instrument

C

CAUTION – Before removing the USB memory stick from the instrument, turn off the
instrument. If you remove the USB memory while the instrument is ON, it may result in memory
malfunction.

C

CAUTION –

Do not

place too much stress on the USB memory stick.

Eject

button

«
...
25
26
27
28
29
...
»

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

DigitalFlow GF868

Бренд: GE Страницы: 80

Бренд: Valor Страницы: 13

Бренд: Campbell Страницы: 31

Бренд: OHAUS Страницы: 26

Бренд: VELOCICALC Страницы: 6

Бренд: Panametrics Страницы: 68

Бренд: Raytech Страницы: 18

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: Raymarine Страницы: 42

Бренд: Keithley Страницы: 343

Бренд: Keithley Страницы: 334

Бренд: La Crosse Technology Страницы: 2

Бренд: Omega Страницы: 170

Бренд: Keithley Страницы: 31

Бренд: Keithley Страницы: 63

Бренд: Keithley Страницы: 18

Бренд: Keithley Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды