Nikon NPL-632 Скачать руководство пользователя | Manualshive

Страница: 26 / 206

background image

2

Preparation

12

Field Station NPL-632 Instruction Manual

C

CAUTION – Before removing the CF card from the instrument, turn off the instrument. If you
remove the card while the instrument is ON, it might result in card malfunction.

C

CAUTION – Nikon recommends that you use the authorized CF card (P/N HXA20657).
Although it may be possible to use other CF cards, the performance and reliability are unknown
and cannot be guaranteed.

Inserting a CF card into the card slot

1.

To open the card slot cover, rotate the knob
clockwise by 90 degrees so that the
protrusion on the knob is set to the OPEN
position.

Note –

Do NOT rotate the knob on the slot cover

beyond the limit as this may damage the knob.

2.

Place the CF card with its blank side facing
outward, and with the connector-side facing
down, and then insert the card into the slot.

Note –

Make sure that you place the card

correctly in relation to the slot before you push the
card into the slot. If the card is not placed
correctly and you then push it too hard in the
wrong direction it may malfunction.

3.

Make sure that the protrusion on the knob is
set to the OPEN (vertical) position and then
close the cover.

OPEN

LOCK

Knob

CF card

Connector

Card slot

Open

position

Lock

position

«
...
24
25
26
27
28
...
»

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

Бренд: LaserLine Страницы: 24

Бренд: Oldham Страницы: 22

YPP-100 Light Piano

Бренд: Yamaha Страницы: 54

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 56

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 32

Disklavier Mark III Series

Бренд: Yamaha Страницы: 39

Бренд: Flytec Страницы: 2

Бренд: Percussion Play Страницы: 3

Бренд: Jula Страницы: 9

LISST-PORTABLE XR

Бренд: Sequoia Страницы: 41

Бренд: Omega Страницы: 13

DIRIS Digiware D-40

Бренд: socomec Страницы: 58

Бренд: SecureAlert, Inc. Страницы: 7

Бренд: GANN Страницы: 89

Бренд: Hanna Instruments Страницы: 2

Ocean Optics HR2000 Series

Бренд: Halma Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды