Nikon NPL-632 Скачать руководство пользователя | Manualshive

Страница: 24 / 206

background image

2

Preparation

10

Field Station NPL-632 Instruction Manual

Charging the battery pack

1.

Connect the power plug on the charger to
an AC power outlet.

2.

Connect the charging plug on the charger
cable to the charging connector on the
battery pack.

Both indicators LED1 and LED2 on the
charger light up orange and charging
starts automatically.

When the battery pack is fully charged,
LED2 changes to green.

Detaching and Re-Attaching the Battery Pack

Detaching the BC-80 battery pack

C

CAUTION – Avoid touching the contacts on the battery pack.

1.

If the instrument is turned on, press

[PWR]

to turn it off.

2.

Set the battery mounting buttons in the
horizontal (UNLOCK) position. To do this,
turn each button inward.

3.

While pressing both battery mounting
buttons, lift the battery pack off the main
body of the instrument.

Attaching the BC-80 battery pack

C

CAUTION – Before you pick up the instrument by the carrying handle, make sure that the
battery pack is clamped securely in place, and that the battery mounting buttons are set in the
vertical (LOCK) position. If the battery pack is not securely fastened, the main unit may come
loose or fall off when you lift the instrument, causing personal injury or instrument damage.

LED1

LED2

LED2

LED1

«
...
22
23
24
25
26
...
»

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

Бренд: ABB Страницы: 20

Бренд: Utilitech Страницы: 2

Бренд: Samson Страницы: 4

Бренд: R&S Страницы: 733

Бренд: R&S Страницы: 369

CP-4900 Micro-GC

Бренд: Varian Страницы: 7

Бренд: Vapotherm Страницы: 2

Бренд: Velleman Страницы: 96

Бренд: Lake Shore Cryotronics Страницы: 97

Бренд: Hanna Instruments Страницы: 9

Бренд: Schneeberger Страницы: 35

Бренд: Flowmetrics Страницы: 102

Бренд: A&D Страницы: 2

Бренд: POSEIDON Страницы: 13

Бренд: Eddy Wireless Страницы: 18

Expert PDU energy 8001

Бренд: Gude Страницы: 22

Бренд: ILITCH ELECTRONICS Страницы: 2

Бренд: Readiness Systems Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды