Nikon NPL-632 Скачать руководство пользователя | Manualshive

Страница: 40 / 206

background image

2

Preparation

26

Field Station NPL-632 Instruction Manual

Face-1/Face-2 Measurements

You can take a measurement from either face of the instrument. To change the face,
rotate the instrument 180° on its base, and rotate the telescope 180° within the
standard.

By averaging the Face-1 and Face-2 measurement values, you can cancel out most
constant mechanical errors. Some errors, such as vertical axis error, cannot be
cancelled out by averaging Face-1 and Face-2 measurements.

C

CAUTION – When rotating the telescope, take care not to catch your finger in the gap between
the instrument’s standard and the telescope.

A Face-1 measurement is made with the vertical circle positioned to the left of the
telescope eyepiece. A Face-2 measurement is made with the vertical circle positioned
to the right of the telescope eyepiece.

Face-1

Face-2

«
...
38
39
40
41
42
...
»

Содержание NPL-632















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-632

Бренд: A&D Страницы: 74

Бренд: Olympus Страницы: 4

Бренд: JENCO Страницы: 13

Бренд: THORLABS Страницы: 21

Бренд: POSEIDON Страницы: 13

Бренд: Fluke Страницы: 5

Бренд: PCE Health and Fitness Страницы: 4

Бренд: MFJ Страницы: 8

Бренд: Fluke Страницы: 97

Бренд: Efergy Страницы: 24

Бренд: HW Group Страницы: 12

Бренд: Oakton Страницы: 10

Бренд: Energenie Страницы: 20

Бренд: Fluke Страницы: 106

Бренд: PRO SIGNAL Страницы: 2

Бренд: YOKOGAWA Страницы: 171

Бренд: Midtronics Страницы: 36

Бренд: Amprobe Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды