Nikon NPL-632 Скачать руководство пользователя

Страница: 29 / 206

Field Station NPL-632 Instruction Manual

Preparation

Insert the large connector of the connecting cable into the correct slot on

your

computer.

Open the slot cover of the instrument. See

Inserting a CF card into the card slot,

page 12

Step 1

Insert the smaller connector of the connecting cable into the USB-B connector
slot on the instrument. See

USB Connecters, page 160

On your office computer, you can now browse to the Mobile Device from where you
can view, copy, or move job files between the office computer and the instrument.

Note –

Before you can use the ActiveSync technology, you need to install the USB

driver software. Download the driver software from the Drivers folder on the
CD-ROM provided with the instrument.

Setting Up the Tripod

CAUTION – The tips of the tripod ferrules are very sharp. When handling or carrying the tripod,
take care to avoid injuring yourself on the ferrules.

Note –

Do not carry the instrument while it is attached to a tripod.

Open the tripod legs enough to for the instrument to be stable.

Locate the tripod directly over the station point. To check the tripod’s position,
look through the center hole in the tripod head.

Firmly press the tripod ferrules into the ground.

Level the top surface of the tripod head.

Note –

If you want to use the plumb bob to center the instrument (see

Centering Using

the Optical Plummet, page 15

), you must level the tripod head precisely.

Securely fasten the thumb screws on the tripod legs.

Place the instrument on the tripod head.

Insert the tripod mounting screw into the center hole of the base plate of the
instrument.

Tighten the tripod mounting screw.

Centering Using the Optical Plummet

When you center the instrument, you align its central axis precisely over the station
point.

Note –

If you require high accuracy, check and adjust the optical plummet before you

center the instrument. For detailed instructions, see

Checking and Adjusting the

Optical Plummet, page 147

Содержание NPL-632















































































































































































































Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды

Nikon NPL-632, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды