Nikon NPL-632 Скачать руководство пользователя

Страница: 36 / 206

Preparation

Field Station NPL-632 Instruction Manual

Setting Up the Prism Reflector

Assemble the prism reflector as shown in

Figure 2.2

Assembling the prism reflector

Adjust the height of the tribrach adapter (see

page 22

If necessary, change the direction of the prism (see

page 23

Set the prism constant (see

page 23

If you are using a single prism holder, set the position of the target plate (see

page 24

Detailed instructions for

Step 2

through

Step 5

are provided on the following pages.

Adjusting the height of the tribrach adapter

The tribrach adapter has two height settings. To use the prism reflector with a
NPL-632 instrument, use the lower height setting.

To adjust the height of the tribrach adapter:

Remove the height adjustment screw
from the tribrach adapter.

Slide the tribrach adapter up or down the
prism holder mount until the height
adjustment screw holes on the prism
holder mount and on the tribrach adapter
are aligned.

Target plate for single prism

Prism C

Tribrach adapter 13/14

Tribrach

Tripod

Tiltable single

prism holder

Target pole

Triple prism holder

Prism holder mount

Height adjustment

screw

Содержание NPL-632















































































































































































































Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды

Nikon NPL-632, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-632

Отзывы:

Похожие инструкции для NPL-632

Бренды по названию

Популярные бренды