– 704 –
CHAPTER 7
Maintenance Commands
Terminal Firmware Search
The range of firmware version is confined by designating the Firmware Version (xx.xx) and Search Condition
(‘!=’, ‘<‘, ‘<=’, ‘==’, ‘>=’, ‘>’).
Note:
The function of Terminal Firmware Search is available for 2-byte firmware version of terminals only.
Result of Search
Pressing Search button lists up the retrieved terminal information after specifying the search conditions of target
terminals.
Click the check box and press Add to the Terminal List button. Selected terminals are added to the Registered
Terminal Information List.
Specify Terminal Area
In this field, target IP terminals can be searched by specifying the range. Select
Station Number
,
Line
Equipment Numbers
, or
IP Address
menu on the drop-down listbox to specify the range, and then click “Area
Search” button.
All
is provided on the drop-down listbox for searching terminals by specifying all the above
three groups. More specific search among the searched result is available by narrowing the range on the list of
Result of Search
.
•
Specify Station Number Area
Select
Station Number
on the drop-down listbox to search for terminals by specific Tenant Number
(TN) and Station Number (STN) range.
START TN:
First tenant number to start searching.
END TN:
Last tenant number to stop searching.
START STN:
First station number to start searching.
END STN:
Last station number to stop searching.
•
Specify Line Equipment Numbers Area
Select
Line Equipment Numbers
on the drop-down listbox to search for terminals by specific Line
Equipment Number (LENS) range.
START LENS: First LENS to start searching.
END LENS:
Last LENS to stop searching.
•
Specify IP Address Area
Select
IP Address
on the drop-down listbox to search for terminals by specific IP address range.
START IP Address: First IP address to start searching.
END IP Address:
Last IP address to stop searching.
[Terminals fitting the search conditions]
The information of IP terminals fitting the search conditions specified on
How to Specify Terminal
and
Specify Terminal Area
are listed. Select an IP terminal on the list and then click “Add to List” button to
add the selected terminal to the “Already Assigned Terminals Information” list. Check the “Select All” but-
ton to select all the IP terminals on the
Terminals fitting the search condition
list.
Содержание SV8500
