![background image](http://html1.mh-extra.com/html/nec/sv8500/sv8500_operation-and-maintenance-manual_3911915788.webp)
– 741 –
CHAPTER 7
Maintenance Commands
CMNT: Control of SR-MGC Maintenance Data (LDM)
1. Function Outline
This command controls the Survivable Remote MGC (SR-MGC) in the remote office. SR-MGC Number, IP
address and office name are specified by this command to recognize the SR-MGC allocated to the MGC in the
main-office. It can also initialize the SR-MGC and display the operation state of the SR-MGC. Office data copy
and changeover can be executed by this command.
Note 1:
When the Update button is clicked, operating state of all the SR-MGCs in the network managed by the
logged-in MGC can be indicated on the list. All the SR-MGCs’ data displayed on the list is output as
a CSV file by clicking the Output CSV File button.
Note 2:
The SR-MGC data cannot be over written on this command.
Note 3:
The following conditions must be considered when performing office data copy.
•
Do not perform any PCPro operations other than CMNT command during office data copy. The
PCPro operation such as login/logoff can cause a copy failure.
•
When using the manual copy function of CMNT command, it must be completed until the office data
copy after the periodic Health Check starts. The manual copy function is canceled when the periodic
Health Check starts. Once the office data copy was canceled, it would not be performed on that day
regardless of ASYDL, SYS1, Indexes 844 and 845 settings.
* To work around the above problem, assign data FF HEX to both ASYD SYS1 INDEX 87 and INDEX
88 to stop the periodic Health Check program before starting the manual office data copy.
2. Parameters
Input Data
Select any of the tabs, Set, Initialize, Office Data Copy, or Operation Mode Changeover to activate the required
operation.
<Setting Tab>
SR-MGC No. [0-255]:
Assign a unique SR-MGC Number to each SR-MGC equipment in remote office.
Office Name [Maximum 20 characters]:
Enter the Office Name of the remote office to which the corresponding SR-MGC belongs.
PBI:
Select the corresponding Local Module Group (LMG). For 1-IMG and 4-IMG system, data 0 is displayed
on the list.
IP Address:
Содержание SV8500
