manualshive.com logo in svg

NEC 78K0S/KA1+, Руководство пользователя

Предварительное руководство пользователя для продукта NEC 78K0S/KA1+ теперь доступно для бесплатного скачивания на нашем сайте. Это подробное руководство поможет вам легко освоить функции этого продукта. Не упустите шанс загрузить его с manualshive.com.

Поделиться
Скачать
background image

APPENDIX  D   LIST  OF  CAUTIONS 

User’s Manual  U16898EJ3V0UD 

388 

 (2/17) 

Chapter 

Classification 

Function Details 

of 

Function 

Cautions Page 

Chapter 5 

Hard 

Crystal/ 
ceramic 
oscillator 

−

 

When using the crystal/ceramic oscillator, wire as follows in the area enclosed by 
the broken lines in Figure 5-6 to avoid an adverse effect from wiring capacitance. 
  • Keep the wiring length as short as possible. 
  • Do not cross the wiring with the other signal lines.  Do not route the wiring 
    near a signal line through which a high fluctuating current flows.   
  • Always make the ground point of the oscillator capacitor the same potential 
    as V

SS

.  Do not ground the capacitor to a ground pattern through which a high 

    current flows. 
  • Do not fetch signals from the oscillator. 

p. 72 

Even if TM00 is read, the value is not captured by CR010. 

pp. 84, 
116 

Hard 

TM00: 16-bit 
timer counter 
00 

When TM00 is read, count misses do not occur, since the input of the count clock 
is temporarily stopped and then resumed after the read. 

pp. 84, 
116 

Set CR000 to other than 0000H in the clear & start mode entered on match 
between TM00 and CR000.  This means a 1-pulse count operation cannot be 
performed when this register is used as an external event counter. 

pp. 85, 
116 

In the free-running mode and in the clear & start mode using the valid edge of the 
TI000 pin, if CR000 is set to 0000H, an interrupt request (INTTM000) is generated 
when CR000 changes from 0000H to 0001H following overflow (FFFFH). 

p.116 

If the new value of CR000 is less than the value of 16-bit timer counter 0 (TM00), 
TM00 continues counting, overflows, and then starts counting from 0 again.  If the 
new value of CR000 is less than the old value, therefore, the timer must be reset 
to be restarted after the value of CR000 is changed. 

pp. 85, 
116 

Soft 

The value of CR000 after 16-bit timer/event counter 00 has stopped is not 
guaranteed. 

pp. 85, 
117 

The capture operation may not be performed for CR000 set in compare mode 
even if a capture trigger is input. 

pp. 85, 
119 

When P31 is used as the input pin for the valid edge of TI010, it cannot be used 
as a timer output (TO00).  Moreover, when P31 is used as TO00, it cannot be 
used as the input pin for the valid edge of TI010. 

pp. 85, 
121 

Hard 

If the register read period and the input of the capture trigger conflict when CR000 
is used as a capture register, the capture trigger input takes precedence and the 
read data is undefined.  Also, if the count stop of the timer and the input of the 
capture trigger conflict, the capture trigger is undefined. 

pp. 85, 
119 

CR000: 16-bit 
timer capture/ 
compare 
register 000 

Changing the CR000 setting may cause a malfunction.  To change the setting, 
refer to 6.5 Cautions Related to 16-Bit Timer/Event Counter 00 (17) Changing 
compare register during timer operation. 

p. 85 

In the free-running mode and in the clear & start mode using the valid edge of the 
TI000 pin, if CR010 is set to 0000H, an interrupt request (INTTM010) is generated 
when CR010 changes from 0000H to 0001H following overflow (FFFFH). 

pp. 86, 
116 

If the new value of CR010 is less than the value of 16-bit timer counter 0 (TM00), 
TM00 continues counting, overflows, and then starts counting from 0 again.  If the 
new value of CR010 is less than the old value, therefore, the timer must be reset 
to be restarted after the value of CR010 is changed. 

pp. 86, 
116 

Soft 

The value of CR010 after 16-bit timer/event counter 00 has stopped is not 
guaranteed. 

pp. 86, 
117 

Chapter 6 

Hard 

16-bit 
timer/ 
event 
counters 
00 

CR010: 16-bit 
capture/ 
compare 
register 010 

The capture operation may not be performed for CR010 set in compare mode 
even if a capture trigger is input. 

pp. 86, 
119 

 

Содержание 78K0S/KA1+



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 78K0S/KA1+

Balboa Instruments EL Series Hot Sheet preview
EL Series
Бренд: Balboa Instruments Страницы: 10
Barthelme CHROMOFLEX RC Instruction Manual preview
CHROMOFLEX RC
Бренд: Barthelme Страницы: 8
Jands SafeGuard Installation Manual preview
SafeGuard
Бренд: Jands Страницы: 7
hager coviva Smartbox TKP100A Operation And Configuration Instructions preview
coviva Smartbox TKP100A
Бренд: hager Страницы: 34
Swagelok BSH 10 Series User Manual preview
BSH 10 Series
Бренд: Swagelok Страницы: 20
Powtran PR5200 Series Manual preview
PR5200 Series
Бренд: Powtran Страницы: 36
Avenview SW-HBT4K-C6-4X4E Quick Start Manual preview
SW-HBT4K-C6-4X4E
Бренд: Avenview Страницы: 8
LAPIS Semiconductor EASE1000 User Manual preview
EASE1000
Бренд: LAPIS Semiconductor Страницы: 34
DPS Telecom NetGuardian LPG D-PK-NGLPG User Manual preview
NetGuardian LPG D-PK-NGLPG
Бренд: DPS Telecom Страницы: 82
Translux Fair-Play MP-50 Series Quick Reference preview
Fair-Play MP-50 Series
Бренд: Translux Страницы: 20
Zonet ZUH2215V Quick Installation Manual preview
ZUH2215V
Бренд: Zonet Страницы: 2
Intrinsyc Open-X 8M User Manual preview
Open-X 8M
Бренд: Intrinsyc Страницы: 38
Omron E53-C4DR4 User Manual preview
E53-C4DR4
Бренд: Omron Страницы: 157
YASKAWA T1000V Technical Manual preview
T1000V
Бренд: YASKAWA Страницы: 444
Hanbay MC DC-2.00 Series User Manual preview
MC DC-2.00 Series
Бренд: Hanbay Страницы: 7
Pilz PNOZ mml1p Operating Manual preview
PNOZ mml1p
Бренд: Pilz Страницы: 23
ARI-Armaturen ARI-PREMIO-Plus 2G Operating And Installation Instructions preview
ARI-PREMIO-Plus 2G
Бренд: ARI-Armaturen Страницы: 52
Braun Group ES-SVC Series User Manual preview
ES-SVC Series
Бренд: Braun Group Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды