Nations N32G43 Series Скачать руководство пользователя

Страница: 320 / 654

Nations Technologies Inc.

Tel

：

+86-755-86309900

：

[email protected]

Address: Nations Tower, #109 Baoshen Road, Hi-tech Park North.
Nanshan District, Shenzhen, 518057, P.R.China

297

631

as it reaches the LPTIM_ARR register value if timer enable. If the one-shot counting mode was previously selected,

setting LPTIM_CTRL.TSTCM bit to 1 will switch the LPTIM to continuous counting mode. Counter will restart as

soon as LPTIM_ARR register value is reached if timer enable.

One-shot mode:

LPTIM_CTRL.SNGMST bit must be set to enable the one-shot mode. A trigger event will re-start the LPTIM.

Hardware will abandon all the trigger events after the internal counter starts and before the counter value equal to

LPTIM_ARR.ARRVAL[15:0] value.

If an external trigger is selected, after each external trigger event that arrivers after the LPTIM_CTRL.SNGMST bit

is set, and after the timer register is stopped (containing a zero value), the timer is restarted for a new count cycle,

as shown in Figure 13-4.

Figure 13-4 PTIM output waveform, single counting mode configuration

One-time mode activated:

The one-time mode is used when the LPTIM_CFG.WAVE bit is set. In one-time mode, the counter is started once

when the first trigger event happens, the hardware will discard any subsequent trigger event, as shown Figure 13-5.

LPTIM_ARR

Compare

PWM

External trigger event

Содержание N32G43 Series















































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание N32G43 Series

Отзывы:

Похожие инструкции для N32G43 Series

Бренды по названию

Популярные бренды

Nations N32G43 Series, Руководство пользователя

Результаты поиска

Содержание N32G43 Series

Отзывы:

Похожие инструкции для N32G43 Series

Бренды по названию

Популярные бренды