Nations N32G43 Series Скачать руководство пользователя

Страница: 601 / 654

Nations Technologies Inc.

Tel

：

+86-755-86309900

：

[email protected]

Address: Nations Tower, #109 Baoshen Road, Hi-tech Park North.
Nanshan District, Shenzhen, 518057, P.R.China

578

631

Bit field

Name

Description

this bit, and then the corresponding interrupt will be triggered. When this bit is

set, if the CAN_INTE.SLKITE bit is set, a state change interrupt will be

generated.

Software can clear this bit, and hardware also clears this bit when

CAN_MSTS.SLPAK bit is cleared.

Notes

: When CAN_INTE.SLKITE=0, this bit should not be queried, but the

CAN_MSTS.SLPAK bit should be queried to know the sleep state.

WKUINT

Wakeup interrupt

When CAN is in sleep state, once the start of frame bit (SOF) is detected, the

hardware will set this bit; And if the CAN_INTE.WKUITE bit is set, a state

change interrupt is generated.

This bit is cleared by software.

ERRINT

Error interrupt

When an error is detected, a bit of the CAN_ESTS register will be set, and if the

corresponding interrupt enable bit of the CAN_INTE register is also set, the

hardware will set this bit; If the CAN_INTE.ERRITE bit is set, a state change

interrupt is generated. This bit is cleared by software.

SLPAK

Sleep acknowledge

This bit is set by hardware, indicating that the software CAN module is in sleep

mode. This bit is the confirmation of the software request to enter sleep mode

( the CAN_MCTRL.SLPRQ bit is set).

Hardware clears this bit when CAN exits sleep mode (CAN leaves Sleep mode

and entering normal mode,it needs to be synchronized with CAN bus).

Synchronization with CAN bus here means that the hardware needs to detect 11

consecutive recessive bits on the RX pin of CAN.

Notes

: clearing CAN_MCTRL.SLPRQ bit by software or hardware will start the

process of exiting sleep mode. See the description of CAN_MCTRL.AWKUM bit

for details of clearing CAN_MCTRL.SLPRQ bit.

INIAK

Initialization acknowledge

This bit is set by hardware, indicating that the software CAN module is in

initialization mode. This bit is the confirmation of the software request to enter

the initialization mode (the CAN_MCTRL.INIRQ bit is set).

Hardware clears this bit when CAN exits initialization mode (CAN leaves

Initialization mode and entering normal mode,it needs to be synchronized with

CAN bus). Synchronization with CAN bus here means that the hardware needs to

detect 11 consecutive recessive bits on the RX pin of CAN.

CAN transmit status register (CAN_TSTS)

Address offset: 0x08

Reset value: 0x1C00 0000

Содержание N32G43 Series















































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание N32G43 Series

Отзывы:

Похожие инструкции для N32G43 Series

Бренды по названию

Популярные бренды

Nations N32G43 Series, Руководство пользователя

Результаты поиска

Содержание N32G43 Series

Отзывы:

Похожие инструкции для N32G43 Series

Бренды по названию

Популярные бренды