MW 790031754 Скачать руководство пользователя страница 9

Страница: 9 / 62

M1.1.TZHD30S-50S.NLFREN - 15032019

5.4 installation

Before beginning assembly, take note of the

following precautions and suggestions.

The machine is bolted to the pallet, before

attempting any of the assembly procedures

remove all of the loose parts and hardware from

the inside of the machine and unbolt the machine

from the pallet.

-----

FLOOR:

This tool distributes a large amount of

weight over a

small area. Make certain that the

floor is capable of

supporting both the weight of the

machine and the

operator. The floor should also be

a level surface.

If the unit wobbles or rocks once in

place, be sure to

eliminate by using shims.

-----

WORKING CLEARANCES:

Take into

consideration the size of the material to be

processed. Make sure that you allow enough

space for

you to operate the machine freely.

-----

OUTLET PLACEMENT:

Outlets should be

located close enough to the machine

so that the

power cord or extension cord is not in an

area

where it would cause a tripping hazard. Be sure

observe all electrical codes if installing new circuits

and/or outlets.

DO NOT assemble the machine until you are

certain that the machine is not plugged in and

the power switch is in the OFF position.

DO NOT connect the machine to the power

source until the machine is completely

assembled and you read and understand the

entire User Manual.

5.4.1Remove the accessories

Remove all attachments fixed to pallet.

Remove all accessories or packages contained in

the cabinet.

5.4.2 Motor cover install

Install the motor cover by inserting the door pins
into the hinge sockets on the cabinet as

Fig.5

;

Fig.5 motor cover install

5.4.3 Hand wheel handle install

Install the handle into the Blade Tilt & Height hand
wheel as

Fig.6.

Fig.6 hand wheel handle install

5.4.4 Extension wings install

(Fig.7)

A. Remove the screws from the sides of the main

table;

B. Inspect the extension wings and main table

mating surfaces for burrs or foreign materials that

may inhibit assembly;

C. The mating edges of the wings and the table

must be clean, smooth, and flat, use a wire brush

or sand paper if necessary to clean up the edges,

this step will ensure that the wings mount properly

to the main table;

D. Attach the wings to the main table with the

screws removed in step A;

E. Place the straightedge across the extension

wings and main table to make sure that the table

surface is flat;

If the outside end of extension wings tilts down Or

up, use a strip of masking tape to shim the

extension wing up or down ;

Fig.7 Extension wings install

Figuur 5 Installatie van de motorkap

5.4 installation

Before beginning assembly, take note of the

following precautions and suggestions.

The machine is bolted to the pallet, before

attempting any of the assembly procedures

remove all of the loose parts and hardware from

the inside of the machine and unbolt the machine

from the pallet.

-----

FLOOR:

This tool distributes a large amount of

weight over a

small area. Make certain that the

floor is capable of

supporting both the weight of the

machine and the

operator. The floor should also be

a level surface.

If the unit wobbles or rocks once in

place, be sure to

eliminate by using shims.

-----

WORKING CLEARANCES:

Take into

consideration the size of the material to be

processed. Make sure that you allow enough

space for

you to operate the machine freely.

-----

OUTLET PLACEMENT:

Outlets should be

located close enough to the machine

so that the

power cord or extension cord is not in an

area

where it would cause a tripping hazard. Be sure

observe all electrical codes if installing new circuits

and/or outlets.

DO NOT assemble the machine until you are

certain that the machine is not plugged in and

the power switch is in the OFF position.

DO NOT connect the machine to the power

source until the machine is completely

assembled and you read and understand the

entire User Manual.

5.4.1Remove the accessories

Remove all attachments fixed to pallet.

Remove all accessories or packages contained in

the cabinet.

5.4.2 Motor cover install

Install the motor cover by inserting the door pins
into the hinge sockets on the cabinet as

Fig.5

;

Fig.5 motor cover install

5.4.3 Hand wheel handle install

Install the handle into the Blade Tilt & Height hand
wheel as

Fig.6.

Fig.6 hand wheel handle install

5.4.4 Extension wings install

(Fig.7)

A. Remove the screws from the sides of the main

table;

B. Inspect the extension wings and main table

mating surfaces for burrs or foreign materials that

may inhibit assembly;

C. The mating edges of the wings and the table

must be clean, smooth, and flat, use a wire brush

or sand paper if necessary to clean up the edges,

this step will ensure that the wings mount properly

to the main table;

D. Attach the wings to the main table with the

screws removed in step A;

E. Place the straightedge across the extension

wings and main table to make sure that the table

surface is flat;

If the outside end of extension wings tilts down Or

up, use a strip of masking tape to shim the

extension wing up or down ;

Fig.7 Extension wings install

Figuur 7 Installatie van de verlengstukken

5.4 installation

Before beginning assembly, take note of the

following precautions and suggestions.

The machine is bolted to the pallet, before

attempting any of the assembly procedures

remove all of the loose parts and hardware from

the inside of the machine and unbolt the machine

from the pallet.

-----

FLOOR:

This tool distributes a large amount of

weight over a

small area. Make certain that the

floor is capable of

supporting both the weight of the

machine and the

operator. The floor should also be

a level surface.

If the unit wobbles or rocks once in

place, be sure to

eliminate by using shims.

-----

WORKING CLEARANCES:

Take into

consideration the size of the material to be

processed. Make sure that you allow enough

space for

you to operate the machine freely.

-----

OUTLET PLACEMENT:

Outlets should be

located close enough to the machine

so that the

power cord or extension cord is not in an

area

where it would cause a tripping hazard. Be sure

observe all electrical codes if installing new circuits

and/or outlets.

DO NOT assemble the machine until you are

certain that the machine is not plugged in and

the power switch is in the OFF position.

DO NOT connect the machine to the power

source until the machine is completely

assembled and you read and understand the

entire User Manual.

5.4.1Remove the accessories

Remove all attachments fixed to pallet.

Remove all accessories or packages contained in

the cabinet.

5.4.2 Motor cover install

Install the motor cover by inserting the door pins
into the hinge sockets on the cabinet as

Fig.5

;

Fig.5 motor cover install

5.4.3 Hand wheel handle install

Install the handle into the Blade Tilt & Height hand
wheel as

Fig.6.

Fig.6 hand wheel handle install

5.4.4 Extension wings install

(Fig.7)

A. Remove the screws from the sides of the main

table;

B. Inspect the extension wings and main table

mating surfaces for burrs or foreign materials that

may inhibit assembly;

C. The mating edges of the wings and the table

must be clean, smooth, and flat, use a wire brush

or sand paper if necessary to clean up the edges,

this step will ensure that the wings mount properly

to the main table;

D. Attach the wings to the main table with the

screws removed in step A;

E. Place the straightedge across the extension

wings and main table to make sure that the table

surface is flat;

If the outside end of extension wings tilts down Or

up, use a strip of masking tape to shim the

extension wing up or down ;

Fig.7 Extension wings install

Figuur 6 Installatie van de handgreep op het handwiel

Handgreep

Vergrendelingsknop

WAARSCHUWING!

Monteer de machine niet zolang u niet zeker bent dat de machine niet aangesloten is en dat de

schakelaar op OFF staat�

Sluit de machine pas aan nadat deze volledig is gemonteerd en u de volledige handleiding heeft

gelezen en begrepen�

Verwijder de accessoires

Verwijder alle bevestigingen op het pallet.

Verwijder alle accessoires en verpakkingen van de machine.

Montage van de motorkap

Installeer de motorkap door de deurpennen in de scharnieren van het frame te steken, zoals getoond op figuur 5.

Montage van het handwiel en de handgreep

Monteer de handgreep in het handwiel voor de instelling van de zaagbladhelling en zaagbladhoogte, zoals op figuur 6.

Montage van de verlengstukken (figuur 7)

1. Verwijder de schroeven aan de zijkanten van de hoofdtafel.

2. Inspecteer de verlengstukken en oppervlakken van de hoofdtafel op bramen of vreemde voorwerpen die de montege

kunnen verhinderen.

3. De randen van de verlengstukken en van de tafel moeten schoon, glad en vlak zijn. Gebruik indien nodig een staalborstel

of schuurpapier om de randen te schuren. Dit zorgt ervoor dat de verlengstukken correct op de hoofdtafel gemonteerd

worden.

4. Bevestig de verlengstukken aan de hoofdtafel met de in stap 1 verwijderde schroeven.

5. Plaats een rechte liniaal over de verlengstukken en de hoofdtafel om te controleren of het oppervlak effen is.

Als de buitenste uiteinde van de verlengstukken omlaag of omhoog kantelt, gebruik dan een plakband of bulplaat om de

positie ervan te corrigeren.

copyrighted

document

- all

rights

reserved

FBC

Содержание 790031754































































Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды

MW 790031754, Руководство пользователя

Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды