MW 790031754 Скачать руководство пользователя страница 40

Страница: 40 / 62

M1.1.TZHD30S-50S.NLFREN - 15032019

2.2 Feature identification

3.2 Feature Identification

( Fig.1)

Fig.1

Rear rail

Main Table

Blade Guard

Right Extension Wing

Fence

Extension Table

Front rail & Tube

Leg

Motor Cover

Blade Height Hand Wheel

On/Off Switch

Dust Port

Blade Tilt Hand Wheel

3.3 Intended Use

Table saw and the workpiece guide equipment
supplied with it are intended to be used exclusively
for the following purposes:

●

Laminated and unlaminated board materials (e.g.

chipboard, coreboard, MDF board, ...)

●

Solid wood •

●

Gypsum plasterboard • , Cardboard, Veneer with

a suitable clamping device

●

Dimensionally stable plastics (thermoset plastics,

thermoplastics).Sawing these materials does not
normally involve any risks in respect of dust, chips,
and thermal degradation products.

Tools:

●

The chosen saw blade must be suitable both for

the specific work cycle and for the specific material.

●

Only circular blades which are solid chrome

vanadium (CV) or  tungsten carbide tipped (TCT)
and have  a diameter of 250mm  , arbor size
30mm,as well as a maximum width of 20mm are
allowed for the main saw

●

Saw blades made of high-alloy high-speed steel

(HSS) are not allowed to be used.

●

Saw blades and their fixing devices shall conform

to EN 847-1:2005

。

Site of installation/use:

●

The machine is not suitable for use outdoors, or in

rooms that are subject to moisture or the risk of
explosions.

●

The intended use of the machine involves

connection to a suitably dimensioned extraction
system .•

●

Intended use also involves compliance with our

specified operating, maintenance and repair

conditions and the safety information contained in
the operating ins9tructions.

●

The table saw may only be used, set up and

maintained by persons who are familiar with the
machine and aware of the dangers.

●

The pertinent accident prevention regulations as

well as any other generally recognised technical
safety and industrial medicine rules must be
observed.

●

Repair work must be carried out by our own

customer service or by an organization that we have
authorized.    Only original spare parts are allowed to
be used for this. we will assume no warranty for any
damage that is caused by using non-original    spare
parts.

The machine is prohibited to be used in a
potentially explosive atmosphere!

1. Rear rail

2. Main table

3. Blade guard

4. Right extension wing

5. Fence

6. Extension table

7. Front rail + tube

8. Leg

9. Motor cover

10. Blade height handwheel

11. On/Off switch

12. Dust port

13. Blade tilt handwheel

Figure 3

2�3 Intended use

Table saw and the workpiece guide equipment supplied with it are intended to be used exclusively for the following purposes:

• Laminated and unlaminated board materials (e.g. chipboard, cardboard, MDF board, ...),

• Solid wood,

• Gypsum plasterboard, cardboard, veneer with a suitable clamping device,

• Dimensionally stable plastics (thermoset plastics, thermoplastics). Sawing these materials does not normally involve any risks

in respect of dust, chips, and thermal degradation products.

Tools:

•

The chosen saw blade must be suitable both for the specific work cycle and for the specific material.

• Only circular blades which are solid chrome vanadium (CV) or tungsten carbide tipped (TCT) and have a diameter of

250 mm , arbor size 30 mm,as well as a maximum width of 20 mm are allowed for the main saw.

• Saw blades made of high-alloy high-speed steel (HSS) are not allowed to be used.

•

Saw blades and their fixing devices shall conform to EN 847-1:2005.

Site of installation/use:

• The machine is not suitable for use outdoors, or in rooms that are subject to moisture or the risk of explosions.

• The intended use of the machine involves connection to a suitably dimensioned extraction system.

•

Intended use also involves compliance with our specified operating, maintenance and repair conditions and the safety

information contained in the operating instructions.

• The table saw may only be used, set up and maintained by persons who are familiar with the machine and aware of the

dangers.

• The pertinent accident prevention regulations as well as any other generally recognised technical safety and industrial

medicine rules must be observed.

• Repair work must be carried out by our own customer service or by an organization that we have authorized. Only

original spare parts are allowed to be used for this. we will assume no warranty for any damage that is caused by using

non-original spare parts.

WARNING!

The machine is prohibited to be used in a potentially explosive atmosphere!

copyrighted

document

- all

rights

reserved

FBC

Содержание 790031754































































Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды

MW 790031754, Руководство пользователя

Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды