manualshive.com logo in svg

MW 790031754, Руководство пользователя, Страница: 2 / 62

Поделиться
Скачать
MW 790031754 Скачать руководство пользователя страница 2

2

NL

M1.1.TZHD30S-50S.NLFREN - 15032019

1  Veiligheid

De veiligheidssymbolen zijn bedoeld om uw aandacht te vestigen op mogelijke gevaarlijke omstandigheden. Deze handleiding 

gebruikt een reeks symbolen en woorden om het belang van veiligheidsberichten aan te geven. Het verloop van de symbolen 

wordt hieronder beschreven:

GEVAAR!

Wijst op een dreigende gevaarlijke situatie die, indien niet vermeden, de dood of ernstige letsels kan veroorzaken.

WAARSCHUWING!

Wijst op een mogelijke gevaarlijke situatie die, indien niet vermeden, de dood of ernstige letsels kan veroorzaken.

AANDACHT!

Wijst op een mogelijke gevaarlijke situatie die, indien niet vermeden, lichte of matige verwondingen kan veroorzaken. 

Kan ook gebruikt worden om praktijken aan te pakken die geen verband hebben met het risico op letsels.

OPMERKING

Symbool dat gebruikt wordt om de gebruiker nuttige informatie te geven over de juiste werking van de machine.

!

Inhoud

1  Veiligheid ������������������������������������������������������������������������������������������������������������������������������������������2

1.1  Veiligheidsvoorschriften ...................................................................................................................................3

1.2  Veiligheidsvoorzieningen .................................................................................................................................4

2  Omschrijving van de machine ������������������������������������������������������������������������������������������������������������5

2.1  Technische gegevens .......................................................................................................................................5

2.2  Omschrijving van de machineelementen ............................................................................................................6

2.3  Toepasselijk gebruik ........................................................................................................................................6

2.4  Vereisten voor stroomvoorziening ......................................................................................................................7

2.5  Geluidsniveau ................................................................................................................................................7

3  Installatie van de machine �����������������������������������������������������������������������������������������������������������������8

3.1  Transport van machines ...................................................................................................................................8

4  Instellingen �������������������������������������������������������������������������������������������������������������������������������������� 14
5  Bediening ���������������������������������������������������������������������������������������������������������������������������������������� 16

5.1  Elektriciteit ...................................................................................................................................................16

5.2  Voorzorgmaatregelen voor gebruik .................................................................................................................16

5.3  Bediening ....................................................................................................................................................16

5.4  Dwarssnijden ...............................................................................................................................................16

5.5  Langssnijden ................................................................................................................................................16

6  Onderhoud �������������������������������������������������������������������������������������������������������������������������������������� 17
7  Storingen oplossen �������������������������������������������������������������������������������������������������������������������������� 18
8  Onderdelen �������������������������������������������������������������������������������������������������������������������������������������53
9  EG conformiteitsverklaring ��������������������������������������������������������������������������������������������������������������� 62

copyrighted 

document 

- all 

rights 

reserved 

by 

FBC

Содержание 790031754































































Отзывы:

Нет отзывов