MW 790031754 Скачать руководство пользователя страница 12

Страница: 12 / 62

M1.1.TZHD30S-50S.NLFREN - 15032019

D. Place a straightedge against the blade and the
spreader. When properly aligned, the
spreader/riving knife will be in the "alignment
zone," shown in

Fig.16

, and will be parallel with the

blade.

Fig.16 alignment zone

After changing a saw blade, always check that the
Riving knife or Blade Guard is correctly set!

A. Riving knives shall be manufactured from steel
with an ultimate tensile strength of 580 N mm-2 or
of a comparable material, have flat sides (within
0,1 mm per 100 mm) and shall have a thickness
less than the width of cut (kerf) and at least 0,2mm
greater than the saw blade plate. As

Fig.17

Key:

e riving knife thickness
b saw blade blade
B kerf(width of saw blade cut)

B. The distance of the riving knife from the gear rim
must be between 3mm and 8mm. measured
radially through the centre of the saw spindle. As

Fig.18

C. The highest point of the riving knife must be set
beneath the topmost teeth.

5.4.9 Extraction system

Dust collector device should be prepared by
customer.
The dust extraction equipment is to be
switched on before commencing machining.

The outlet diameter is 100mm.

Fig.19

Air current speed is 20m/s for vacuum suction dust
emission index,  when air current speed of dust
collector device (in accordance with EN
12779:2004) is not lower than 20m/s,  ensure
machine can be normal exhausted.

1. Required air flow: 800 m3/h;
2. Ensure pressure drop of each dust collector

outlet carrying air current speed: 1100Pa

3. Dry chips: 20m/s.
4. Wet chips: 28m/s. (water content is equal

to18%)

Fig.19

Figuur 17

D. Place a straightedge against the blade and the
spreader. When properly aligned, the
spreader/riving knife will be in the "alignment
zone," shown in

Fig.16

, and will be parallel with the

blade.

Fig.16 alignment zone

After changing a saw blade, always check that the
Riving knife or Blade Guard is correctly set!

Fig.17

Key:

e riving knife thickness
b saw blade blade
B kerf(width of saw blade cut)

B. The distance of the riving knife from the gear rim
must be between 3mm and 8mm. measured
radially through the centre of the saw spindle. As

Fig.18

C. The highest point of the riving knife must be set
beneath the topmost teeth.

5.4.9 Extraction system

Dust collector device should be prepared by
customer.
The dust extraction equipment is to be
switched on before commencing machining.

The outlet diameter is 100mm.

Fig.19

1. Required air flow: 800 m3/h;
2. Ensure pressure drop of each dust collector

outlet carrying air current speed: 1100Pa

3. Dry chips: 20m/s.
4. Wet chips: 28m/s. (water content is equal

to18%)

Fig.19

Figuur 18

D. Place a straightedge against the blade and the
spreader. When properly aligned, the
spreader/riving knife will be in the "alignment
zone," shown in

Fig.16

, and will be parallel with the

blade.

Fig.16 alignment zone

After changing a saw blade, always check that the
Riving knife or Blade Guard is correctly set!

Fig.17

Key:

e riving knife thickness
b saw blade blade
B kerf(width of saw blade cut)

B. The distance of the riving knife from the gear rim
must be between 3mm and 8mm. measured
radially through the centre of the saw spindle. As

Fig.18

C. The highest point of the riving knife must be set
beneath the topmost teeth.

5.4.9 Extraction system

Dust collector device should be prepared by
customer.
The dust extraction equipment is to be
switched on before commencing machining.

The outlet diameter is 100mm.

Fig.19

1. Required air flow: 800 m3/h;
2. Ensure pressure drop of each dust collector

outlet carrying air current speed: 1100Pa

3. Dry chips: 20m/s.
4. Wet chips: 28m/s. (water content is equal

to18%)

Fig.19

Figuur 16 Uitlijningszone

Zaagblad

Spouwmes

Uitlijnings-

zone

D. Place a straightedge against the blade and the
spreader. When properly aligned, the
spreader/riving knife will be in the "alignment
zone," shown in

Fig.16

, and will be parallel with the

blade.

Fig.16 alignment zone

After changing a saw blade, always check that the
Riving knife or Blade Guard is correctly set!

Fig.17

Key:

e riving knife thickness
b saw blade blade
B kerf(width of saw blade cut)

B. The distance of the riving knife from the gear rim
must be between 3mm and 8mm. measured
radially through the centre of the saw spindle. As

Fig.18

C. The highest point of the riving knife must be set
beneath the topmost teeth.

5.4.9 Extraction system

Dust collector device should be prepared by
customer.
The dust extraction equipment is to be
switched on before commencing machining.

The outlet diameter is 100mm.

Fig.19

1. Required air flow: 800 m3/h;
2. Ensure pressure drop of each dust collector

outlet carrying air current speed: 1100Pa

3. Dry chips: 20m/s.
4. Wet chips: 28m/s. (water content is equal

to18%)

Fig.19

Figuur 19

Stofzuig-

mond

(100 mm)

4. Plaats een liniaal tegen het zaagblad en het spouwmes. Als de uitlijning juist is, zal het spouwmes zich in de

uitlijningszone bevinden, zoals getoond op figuur 16, en parallel met het zaagblad zijn.

OPMERKING

Controleer altijd na het vervangen van het zaagblad, dat het spouwmes of de

zaagbladbescherming correct ingesteld is�

1. Spouwmessen moeten gemaakt zijn van staal met een maximale treksterkte van 580 N/mm² of gelijkaardig materiaal,

vlakke kanten hebben (binnen de grens van 0,1 mm per 100 mm) en een dikte die kleiner is dan de snijbreedte

(insnijding) en groter van minstens 0,2 mm dan deze van het zaagblad (figuur 17).

2. De afstand tussen het spouwmes en het tandwiel moet tussen 3 en 8 mm liggen, gemeten door het midden van de zaagas

(figuur 18).

3. Het hoogste punt van het spouwmes moet onder de boventanden ingesteld worden.

Afzuigsysteem

OPMERKING

De gebruiker moet een stofafzuigsysteem installeren�

De stofzuiger moet voor het begin van de bewerking ingeschakeld worden�

De uitlaatdiameter is 100 mm (figuur 19).

De luchtstroomsnelheid is 20 m/s voor de zuigstofemissie. Wanneer de luchtstroomsnelheid van de stofzuiger(conform

EN 12779:2004) niet lager is dan 20 m/s, zorg ervoor dat de machine normaal afgezogen kan worden.

1. Vereist luchtdebiet: 800 m³/h.

2. Zorg voor het drukverlies van elke stofzuiger die de luchtstroomsnelheid draagt: 1100 Pa.

3. Droge spanen: 20 m/s

4. Vochtige spanen: 28 m/s (watergehalte gelijk aan 18%)

copyrighted

document

- all

rights

reserved

FBC

Содержание 790031754































































Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды

MW 790031754, Руководство пользователя

Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды