MW 790031754 Скачать руководство пользователя страница 48

Страница: 48 / 62

M1.1.TZHD30S-50S.NLFREN - 15032019

6. Adjustment

Before operation, the machine should be
carefully adjusted for best performance. Please
make adjustment as following:

6.1 Blade Raising and Tilting Machine

To raise or lower the blade, loosen lock knob (C)
As

Fig.20

and turn the raising hand wheel (D).

When desired height is obtained, retighten lock
knob. The blade

should be raised 1/8” to 1/4”

above the top surface of the material being cut.
With hollow ground blades the blade should be
raised to the maximum to provide chip clearance.
To tilt the saw blade, loosen lock knob (B) and turn
tilting hand wheel (A). When desired angle is
obtained, retighten lock knob. See

Fig.20.

Fig.20

6.2 Adjusting Rip fence

1. The rip fence must be perfectly aligned with the
table T-slot, to verify this, align the edge of the rip
fence with the table T-slot and lower the locking
lever (A)

Fig.21

to lock in into place. Check to see

if the edge of the rip fence and the table T-slot are
parallel. If they are not parallel, unlock the rip fence
and turn it upside down. Adjust the set screws (H)
as

Fig.22

in or out, verify your adjustment, repeat if

necessary.

2. The lock lever pressure can be adjusted by
loosening the front lock nuts (B) as

Fig.21

and

adjusting the set screws (C) the same amount,

make sure the fence remains parallel with the table
T-slot. Retighten lock nuts.

3. To set the fence perpendicular to the table, place
a square on the table and against the side of the
fence, loosen the top lock nuts (D) and adjust the
setscrews (E) until the fence is perpendicular.
Retighten lock nuts.

4. The pointer window (F) as

Fig.21

position can

be adjusted if needed, loosen pan head screws (G),
reposition the pointer window and retighten pan
head screws.

Fig.21

Fig.22

6.3 Aligning Table T-slot Parallel with Blade

1, The table T-slot must be aligned parallel with the
blade. Using a combination  square  measure the
distance from the back edge of the blade to the
table T-slot.  Pivot blade forward 180º and
re-measure the distance  using the  exact same
point on the blade. The difference between both
measurements must be less than 0.2mm.

(Fig.23)

Figure 21

6. Adjustment

Before operation, the machine should be
carefully adjusted for best performance. Please
make adjustment as following:

6.1 Blade Raising and Tilting Machine

To raise or lower the blade, loosen lock knob (C)
As

Fig.20

and turn the raising hand wheel (D).

When desired height is obtained, retighten lock
knob. The blade

should be raised 1/8” to 1/4”

Fig.20.

Fig.20

6.2 Adjusting Rip fence

1. The rip fence must be perfectly aligned with the
table T-slot, to verify this, align the edge of the rip
fence with the table T-slot and lower the locking
lever (A)

Fig.21

to lock in into place. Check to see

if the edge of the rip fence and the table T-slot are
parallel. If they are not parallel, unlock the rip fence
and turn it upside down. Adjust the set screws (H)
as

Fig.22

in or out, verify your adjustment, repeat if

necessary.

2. The lock lever pressure can be adjusted by
loosening the front lock nuts (B) as

Fig.21

and

adjusting the set screws (C) the same amount,

make sure the fence remains parallel with the table
T-slot. Retighten lock nuts.

4. The pointer window (F) as

Fig.21

position can

be adjusted if needed, loosen pan head screws (G),
reposition the pointer window and retighten pan
head screws.

Fig.21

Fig.22

6.3 Aligning Table T-slot Parallel with Blade

(Fig.23)

Figure 22

6. Adjustment

Before operation, the machine should be
carefully adjusted for best performance. Please
make adjustment as following:

6.1 Blade Raising and Tilting Machine

To raise or lower the blade, loosen lock knob (C)
As

Fig.20

and turn the raising hand wheel (D).

When desired height is obtained, retighten lock
knob. The blade

should be raised 1/8” to 1/4”

Fig.20.

Fig.20

6.2 Adjusting Rip fence

1. The rip fence must be perfectly aligned with the
table T-slot, to verify this, align the edge of the rip
fence with the table T-slot and lower the locking
lever (A)

Fig.21

to lock in into place. Check to see

if the edge of the rip fence and the table T-slot are
parallel. If they are not parallel, unlock the rip fence
and turn it upside down. Adjust the set screws (H)
as

Fig.22

in or out, verify your adjustment, repeat if

necessary.

2. The lock lever pressure can be adjusted by
loosening the front lock nuts (B) as

Fig.21

and

adjusting the set screws (C) the same amount,

make sure the fence remains parallel with the table
T-slot. Retighten lock nuts.

4. The pointer window (F) as

Fig.21

position can

be adjusted if needed, loosen pan head screws (G),
reposition the pointer window and retighten pan
head screws.

Fig.21

Fig.22

6.3 Aligning Table T-slot Parallel with Blade

(Fig.23)

Figure 20

4 Adjustment

NOTICE

Before operation, the machine should be carefully adjusted for best performance� Please make

adjustment as following:

Blade raising and tilting mechanism

To raise or lower the blade, loosen lock knob (C) as on figure 20 and turn the raising handwheel (D). When desired height is

obtained, retighten lock knob. The blade should be raised 1/8” to 1/4” above the top surface of the material being cut. With

hollow ground blades the blade should be raised to the maximum to provide chip clearance. To tilt the saw blade, loosen lock

knob (B) and turn tilting handwheel (A). When desired angle is obtained, retighten lock knob. See figure 20.

Adjusting rip fence

1. The rip fence must be perfectly aligned with the table T-slot, to verify this, align the edge of the rip fence with the table T-slot

and lower the locking lever (A) figure 21 to lock in into place. Check to see if the edge of the rip fence and the table T-slot

are parallel. If they are not parallel, unlock the rip fence and turn it upside down. Adjust the set screws (H) as on figure 22

in or out, verify your adjustment, repeat if necessary.

The lock lever pressure can be adjusted by loosening the front lock nuts (B) as on figure 21 and adjusting the set screws (C)

the same amount, make sure the fence remains parallel with the table T-slot. Retighten lock nuts.

3. To set the fence perpendicular to the table, place a square on the table and against the side of the fence, loosen the top

lock nuts (D) and adjust the setscrews (E) until the fence is perpendicular. Retighten lock nuts.

The pointer window (F) as on figure 21 position can be adjusted if needed, loosen pan head screws (G), reposition the

pointer window and retighten pan head screws.

copyrighted

document

- all

rights

reserved

FBC

Содержание 790031754































































Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды

MW 790031754, Руководство пользователя

Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды