MW 790031754 Скачать руководство пользователя страница 41

Страница: 41 / 62

M1.1.TZHD30S-50S.NLFREN - 15032019

2�4 Requirements of electrical power

List of the most using and prewired voltage:

Motor

4 kW (5.5 HP)

Voltage

380 V

Phase

3 Ph

Frequency

50 Hz

Nominal current

8.3 A

Prewired

380 V / 3 Ph

Cords

The steady-state AC power supply is 0.9 ~ 1.1 times of the rated value.

Frequency

0.99 ~ 1.01 times of rated frequency ( 50 Hz , continuous working)

0.98 ~ 1.02 times of rated frequency(50 Hz, short period working)

Harmonics

The sum of 2nd - 5th distorted harmonic must not exceed 10% of RMS of voltage. An additional 2% of RMS of line voltage is

allowed to for the sum of 6th - 30th harmonic.

Unbalanced voltage

Neither Negative nor zero sequence components is allowed to exceed 2% of the positive sequence component.

Electrical protection

End user should provide protection device against overvoltage due to lightning and short-circuited protection device at the

power supply.

Ingress Protection at the inlet of incoming power cable

The incoming method of incoming cable should ensure IP54 protection class when finishing installation on the spot.

2�5 Noise

Reference standards

The measurements of noise emission were conducted according to the EN ISO 11202 for the determination of sound pressure

level at the operation positions. When the measured sound pressure levels at the operation positions exceed 85 dB(A), the

measurements of sound power levels were conducted according to EN ISO 3746.

Operating conditions

The operating conditions for noise measurement comply with Annex A of ISO 7960:1995.

Testing results

NO LOAD

LOAD

Lwa

101.3

104.1

Lpa

Position A

84.7

88.5

Position B

86.1

89.1

Position C

77.0

79.8

Associated uncertainty

= 4 dB

Note: Background noise of measurement surrounding is 65�0 dB(A)�

copyrighted

document

- all

rights

reserved

FBC

Содержание 790031754































































Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды

MW 790031754, Руководство пользователя

Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды