MW 790031754 Скачать руководство пользователя страница 34

Страница: 34 / 62

M1.1.TZHD30S-50S.NLFREN - 15032019

8. Maintenance

This table saw requires very little maintenance
other than minor lubrication and cleaning. The
following sections detail what will need to be done
in order to assure continued operation of your saw.

LUBRICATION

The table saw has sealed lubricated bearings in
the motor housing and the arbor assembly, they
will not require any additional lubrication. Use a
wire brush to clean off the worm gears and
trunnions and apply a white lithium grease to keep
them lubricated

CLEANING

Cleaning the Model is relatively  easy. Vacuum
excess wood chips and sawdust, and wipe off the
remaining dust with a dry cloth.  If any resin has
built up, use a resin dissolving cleaner to remove it.
After cleaning, treat all unpainted cast iron and
steel with a non-staining lubricant.
Occasionally it will become necessary to clean the
internal parts with more than a vacuum. To do this,
remove the table top and clean the internal parts
with resin/pitch dissolver or mineral spirits  and a
stiff wire brush or steel wool.
Make sure the internal workings are dry before
using the saw again, so that wood dust will not
accumulate. If any essential lubrication is removed
during cleaning, re-lubricate those areas.

CHANGING BELTS
WARNING: MAKE SURE THE POWER CORD IS
DISCONNECTED FROM THE POWER SOURCE!

1. Lower the blade completely, then open the
motor cover (right side), remove the window cover
(left side), see

Fig.28.

2. Loosen the hex nuts A that secure the motor and
raise the motor fully to remove tension on the
V-belts. Roll the V-belts off of the arbor and motor
pulleys.
3. While continuing to raise the motor, install a new
matching set of V-belts onto the pulleys, lower the
motor to tension the V-belts, then tighten the hex
nuts.
4. Close the motor cover and window cover.

Fig.28

Écrou

hexagonal

Figure 28

6 Entretien

Cette scie à table nécessite très peu d’entretien, à l’exception d’un

minimum de lubrification et de nettoyage. Les paragraphes suivants

détaillent ce qui doit être fait pour garantir un fonctionnement continu de

votre machine.

Lubrification

La scie à table possède des roulements lubrifiés étanches dans le

carter du moteur et l’assemblage de l’axe, qui ne nécessitent aucune

lubrification supplémentaire.

Utilisez une brosse métallique pour nettoyer les engrenages à vis sans fin

et les tourillons, et appliquez de la graisse blanche au lithium pour les

maintenir lubrifiés.

Nettoyage

Le nettoyage de la machine est relativement facile. Aspirez les copeaux de bois et la poussière de sciage, et essuyez la

poussière résiduelle avec un chiffon sec. Si de la résine reste collée, enlevez-la avec un nettoyant dissolvant la résine.

Après le nettoyage, traitez les parties en fonte non peinte avec un lubrifiant qui ne tache pas.

Occasionnellement, il sera nécessaire de nettoyer l’intérieur de la machine mieux qu’avec un aspirateur. Pour ce faire, enlevez

le dessus de la table et nettoyez les parties intérieures avec un dissolvant de résine ou de l’essence minérale et une brosse

métallique ou de la laine d’acier.

Assurez-vous que les pièces internes soient sèches avant de remettre la scie en service, pour éviter l’accumulation de poussière

de bois. Si du lubrifiant a été enlevé lors du nettoyage, lubrifiez à nouveau les endroits où c’est nécessaire.

Remplacement des courroies

AVERTISSEMENT !

Assurez-vous que la machine est débranchée !

1. Abaissez complètement la lame, puis ouvrez le capot du moteur (côté droit). Enlevez le couvercle transparent

(voir figure 28).

Desserrez les écrou hexagonaux A qui fixent le moteur et soulevez complètement le moteur pour détendre les courroies

trapézoïdales. Enlevez les courroies de l’axe et des poulies.

3. Tout en continuant à soulever le moteur, installez le nouveau set de courroies trapézoïdales. Ensuite, abaissez le moteur

pour tendre les courroies et resserrez les écrous hexagonaux.

4. Fermez le capot du moteur et le couvercle transparent.

Quand c’est fait, la pièce reste sur la table, s’incline légèrement et est attrapée par l’extrémité arrière de la protection de la

lame, ou glisse de la table et tombe sur le sol. Il est possible aussi que l’alimentation continue jusqu’au bout de la table, après

quoi la pièce est soulevée et ramenée le long du bord extérieur du guide. Les déchets restent sur la table et ne peuvent pas être

touchés avec les mains tant que la scie est en mouvement, sauf s’il s’agit d’une grosse pièce permettant un enlèvement sûr.

copyrighted

document

- all

rights

reserved

FBC

Содержание 790031754































































Результаты поиска

Содержание 790031754

Отзывы:

MW 790031754, Руководство пользователя, Страница: 34 / 62

Результаты поиска

Содержание 790031754

Отзывы: