MW 790031754 Скачать руководство пользователя страница 43

Страница: 43 / 62

M1.1.TZHD30S-50S.NLFREN - 15032019

5.4 installation

Before beginning assembly, take note of the

following precautions and suggestions.

The machine is bolted to the pallet, before

attempting any of the assembly procedures

remove all of the loose parts and hardware from

the inside of the machine and unbolt the machine

from the pallet.

-----

FLOOR:

This tool distributes a large amount of

weight over a

small area. Make certain that the

floor is capable of

supporting both the weight of the

machine and the

operator. The floor should also be

a level surface.

If the unit wobbles or rocks once in

place, be sure to

eliminate by using shims.

-----

WORKING CLEARANCES:

Take into

consideration the size of the material to be

processed. Make sure that you allow enough

space for

you to operate the machine freely.

-----

OUTLET PLACEMENT:

Outlets should be

located close enough to the machine

so that the

power cord or extension cord is not in an

area

where it would cause a tripping hazard. Be sure

observe all electrical codes if installing new circuits

and/or outlets.

DO NOT assemble the machine until you are

certain that the machine is not plugged in and

the power switch is in the OFF position.

DO NOT connect the machine to the power

source until the machine is completely

assembled and you read and understand the

entire User Manual.

5.4.1Remove the accessories

Remove all attachments fixed to pallet.

Remove all accessories or packages contained in

the cabinet.

5.4.2 Motor cover install

Install the motor cover by inserting the door pins
into the hinge sockets on the cabinet as

Fig.5

;

Fig.5 motor cover install

5.4.3 Hand wheel handle install

Install the handle into the Blade Tilt & Height hand
wheel as

Fig.6.

Fig.6 hand wheel handle install

5.4.4 Extension wings install

(Fig.7)

A. Remove the screws from the sides of the main

table;

B. Inspect the extension wings and main table

mating surfaces for burrs or foreign materials that

may inhibit assembly;

C. The mating edges of the wings and the table

must be clean, smooth, and flat, use a wire brush

or sand paper if necessary to clean up the edges,

this step will ensure that the wings mount properly

to the main table;

D. Attach the wings to the main table with the

screws removed in step A;

E. Place the straightedge across the extension

wings and main table to make sure that the table

surface is flat;

If the outside end of extension wings tilts down Or

up, use a strip of masking tape to shim the

extension wing up or down ;

Fig.7 Extension wings install

Figure 5 Motor cover installation

5.4 installation

Before beginning assembly, take note of the

following precautions and suggestions.

The machine is bolted to the pallet, before

attempting any of the assembly procedures

remove all of the loose parts and hardware from

the inside of the machine and unbolt the machine

from the pallet.

-----

FLOOR:

This tool distributes a large amount of

weight over a

small area. Make certain that the

floor is capable of

supporting both the weight of the

machine and the

operator. The floor should also be

a level surface.

If the unit wobbles or rocks once in

place, be sure to

eliminate by using shims.

-----

WORKING CLEARANCES:

Take into

consideration the size of the material to be

processed. Make sure that you allow enough

space for

you to operate the machine freely.

-----

OUTLET PLACEMENT:

Outlets should be

located close enough to the machine

so that the

power cord or extension cord is not in an

area

where it would cause a tripping hazard. Be sure

observe all electrical codes if installing new circuits

and/or outlets.

DO NOT assemble the machine until you are

certain that the machine is not plugged in and

the power switch is in the OFF position.

DO NOT connect the machine to the power

source until the machine is completely

assembled and you read and understand the

entire User Manual.

5.4.1Remove the accessories

Remove all attachments fixed to pallet.

Remove all accessories or packages contained in

the cabinet.

5.4.2 Motor cover install

Install the motor cover by inserting the door pins
into the hinge sockets on the cabinet as

Fig.5

;

Fig.5 motor cover install

5.4.3 Hand wheel handle install

Install the handle into the Blade Tilt & Height hand
wheel as

Fig.6.

Fig.6 hand wheel handle install

5.4.4 Extension wings install

(Fig.7)

A. Remove the screws from the sides of the main

table;

B. Inspect the extension wings and main table

mating surfaces for burrs or foreign materials that

may inhibit assembly;

C. The mating edges of the wings and the table

must be clean, smooth, and flat, use a wire brush

or sand paper if necessary to clean up the edges,

this step will ensure that the wings mount properly

to the main table;

D. Attach the wings to the main table with the

screws removed in step A;

E. Place the straightedge across the extension

wings and main table to make sure that the table

surface is flat;

If the outside end of extension wings tilts down Or

up, use a strip of masking tape to shim the

extension wing up or down ;

Fig.7 Extension wings install

Figure 7 Extension wings install

5.4 installation

Before beginning assembly, take note of the

following precautions and suggestions.

The machine is bolted to the pallet, before

attempting any of the assembly procedures

remove all of the loose parts and hardware from

the inside of the machine and unbolt the machine

from the pallet.

-----

FLOOR:

This tool distributes a large amount of

weight over a

small area. Make certain that the

floor is capable of

supporting both the weight of the

machine and the

operator. The floor should also be

a level surface.

If the unit wobbles or rocks once in

place, be sure to

eliminate by using shims.

-----

WORKING CLEARANCES:

Take into

consideration the size of the material to be

processed. Make sure that you allow enough

space for

you to operate the machine freely.

-----

OUTLET PLACEMENT:

Outlets should be

located close enough to the machine

so that the

power cord or extension cord is not in an

area

where it would cause a tripping hazard. Be sure

observe all electrical codes if installing new circuits

and/or outlets.

DO NOT assemble the machine until you are

certain that the machine is not plugged in and

the power switch is in the OFF position.

DO NOT connect the machine to the power

source until the machine is completely

assembled and you read and understand the

entire User Manual.

5.4.1Remove the accessories

Remove all attachments fixed to pallet.

Remove all accessories or packages contained in

the cabinet.

5.4.2 Motor cover install

Install the motor cover by inserting the door pins
into the hinge sockets on the cabinet as

Fig.5

;

Fig.5 motor cover install

5.4.3 Hand wheel handle install

Install the handle into the Blade Tilt & Height hand
wheel as

Fig.6.

Fig.6 hand wheel handle install

5.4.4 Extension wings install

(Fig.7)

A. Remove the screws from the sides of the main

table;

B. Inspect the extension wings and main table

mating surfaces for burrs or foreign materials that

may inhibit assembly;

C. The mating edges of the wings and the table

must be clean, smooth, and flat, use a wire brush

or sand paper if necessary to clean up the edges,

this step will ensure that the wings mount properly

to the main table;

D. Attach the wings to the main table with the

screws removed in step A;

E. Place the straightedge across the extension

wings and main table to make sure that the table

surface is flat;

If the outside end of extension wings tilts down Or

up, use a strip of masking tape to shim the

extension wing up or down ;

Fig.7 Extension wings install

Figure 6 Handwheel handle installation

Handle

Lock knob

WARNING!

Do not assemble the machine until you are certain that the machine is not plugged in and the

power switch is in the OFF position�

Do not connect the machine to the power source until the machine is completely assembled and

you read and understand the entire user manual�

Remove the accessories

Remove all attachments fixed to pallet.

Remove all accessories or packages contained in the cabinet.

Motor cover install

Install the motor cover by inserting the door pins into the hinge sockets on the cabinet as on figure 5.

Handwheel handle installation

Install the handle into the blade tilt and height handwheel as on figure 6.

Extension wings installation (figure 7)

1. Remove the screws from the sides of the main table.

2. Inspect the extension wings and main table mating surfaces for burrs or foreign materials that may inhibit assembly.

The mating edges of the wings and the table must be clean, smooth, and flat, use a wire brush or sand paper if necessary

to clean up the edges, this step will ensure that the wings mount properly to the main table.

4. Attach the wings to the main table with the screws removed in step 1.

Place the straightedge across the extension wings and main table to make sure that the table surface is flat.

If the outside end of extension wings tilts down or up, use a strip of masking tape to shim the extension wing up or down.

copyrighted

document

- all

rights

reserved

FBC

Содержание 790031754































































Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды

MW 790031754, Руководство пользователя

Результаты поиска

Содержание 790031754

Отзывы:

Похожие инструкции для 790031754

Бренды по названию

Популярные бренды