MW 790031754 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 62

background image

13

NL

M1.1.TZHD30S-50S.NLFREN - 15032019

5.4.10 Electrical installation

Wiring should only be done by professional
electricians. Always make sure the machine is
properly earthed.

All wirings in the cabinets should be protected

against direct contact to at least IP2X when

finishing electrical installation.

All exposed conductive parts should be

connected to the protective bonding circuit.

Close and lock the door of cabinets

。

Enough space around the machine and the

cabinets should be kept in order to maintain

conveniently.

The machine should be installed in a workshop

with good illumination and ventilation.

Over-voltage protection device should be

provided by end user on spot.

Check that the voltage and frequency required by

the machine, shown on the machine’s name plate,

correspond to the electric power supply voltage
and frequency.
The circuit breaker shall be installed for supplying
electric power to this machine, in order to protect
people against electrical shock due to indirect
shock

Wiring:

Finish electrical connection according to the
electrical drawings.
The wirings on the spot should refer to the
requirements of Clause 13 (Wring practices) of EN
60204-1:2006.

Checking:

After finishing wiring on the spot, check  the
following items at least:
Check the wirings of machine.
Check the direction of motors and change wiring if
necessary.
Check the components  for defects, such as
loosening or damage.
Check the functions of safety d

ELECTRICAL CONNECTIONS

Elektrische installatie

WAARSCHUWING!

• De bekabeling moet door professionele elektriciens uitgevoerd worden� Zorg er altijd voor dat

de machine correct geaard is�

• De bekabeling in de machine moeten na het einde van de elektrische installatie tegen een

direct contact beschermd worden met een beschermingsgraad van minstens IP2X�

• Alle blootgestelde geleidenden delen moeten op het aardingscircuit aangesloten worden�

• Sluit en vergrendel de deur van de kasten�

OPMERKING

• Een voldoende ruimte moet rond de machine en de kasten vrij gehouden worden, om het

onderhoud ervan te vergemakkelijken�

• De machine moet in een goed verlichte en geventileerde werkplaats geïnstalleerd worden�

• De overbelastingsbeveiliging moet door de gebruiker ter plaatse aangebracht worden�

Controleer dat de door de machine vereiste spanning en frequentie, die op de naamplaat vermeld zijn, met de spanning en

frequentie van de stroomvoeding overeenstemmen.

Een stroomonderbreker moet op de stroomvoeding geïnstalleerd worden, om mensen te beschermen tegen elektrische schokken

als gevolg van indirecte schokken.

Bekabeling:

Voer de elektrische aansluitingen uit volgens de schakelschema’s.

De bekabeling ter plaatse moet voldoen aan de eisen van punt 13 (bedradingspraktijken) van de norm EN 60204-1:2006).

Controle:

Controleer na voltooiing van de bekabeling ter plaatse ten minste de volgende punten:

• Controleer de bekabeling van de machine.

• Controleer de draairichting van de motor en wijzig de bekabeling indien nodig.

• Controleer of componenten defect, los of beschadigd zijn.

• Controleer de werking van de veiligheidsvoorzieningen.

!

copyrighted

document

- all

rights

reserved

by

FBC

«
...
11
12
13
14
15
...
»

Содержание 790031754































































Отзывы:

Нет отзывов

Похожие инструкции для 790031754

Бренд: Ferm Страницы: 108

Pro-Power VISCB20

Бренд: VITO Страницы: 64

Бренд: Inmes Страницы: 28

Бренд: Betax PRO Страницы: 26

Бренд: General International Страницы: 36

Бренд: Ryobi Страницы: 146

Бренд: KRESS Страницы: 12

Бренд: KRESS Страницы: 184

Sunjoe 24V-MPSWVG-LTE

Бренд: SNOWJOE Страницы: 20

Бренд: Ferm Страницы: 52

Бренд: Ferm Страницы: 44

Бренд: Ferm Страницы: 72

Бренд: Scotts Страницы: 42

Production Cutting Bandsaw

Бренд: Bahco Страницы: 4

Бренд: Workzone Страницы: 34

Бренд: Workzone Страницы: 48

Бренд: KRESS Страницы: 12

Бренд: Haussmann Xpert Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды