MR VACUTAP VR Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 268

background image

2 Safety

Maschinenfabrik Reinhausen GmbH 2015

15

4349315/00 EN

VACUTAP® VR®

Safety

General safety information

This technical file contains detailed descriptions of the safe and proper in-
stallation, connection, and commissioning of the product.
▪

Read this technical file through carefully to familiarize yourself with the
product.

▪

Particular attention should be paid to the information given in this chap-
ter.

Appropriate use

If used as intended and in compliance with the requirements and conditions
specified in this technical file as well as the warning notices in this technical
file and attached to the product, then the product does not present any haz-
ards to people, property or the environment. This applies throughout the
product's entire life, from delivery through installation and operation to disas-
sembly and disposal.

The operational quality assurance system ensures a consistently high quality
standard, particularly in regard to the observance of health and safety re-
quirements.

The following is considered appropriate use
▪

Only operate the product in accordance with this technical file and the
agreed delivery conditions and technical data

▪

Use the equipment and special tools supplied solely for the intended
purpose and in accordance with the specifications of this technical file

▪

Use the product only with the transformer specified in the order

▪

You will find the standard valid for the product and the year of issue on
the name plate

▪

The serial numbers of on-load tap-changers and on-load tap-changer
accessories (drive, drive shaft, bevel gear, protective relay etc.) must
match if the on-load tap-changers and on-load tap-changer accessories
are supplied as a set for one order.

The on-load tap-changer is not intended to be used with an oil filter unit.

2

2.1

2.2

«
...
13
14
15
16
17
...
»

Содержание VACUTAP VR













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: NEC Страницы: 29

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренд: Baker Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды