MR VACUTAP VR Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 268

background image

6 Assembly: Bell-type tank design

Maschinenfabrik Reinhausen GmbH 2015

114

4349315/00 EN

VACUTAP® VR®

Vapor-phase drying in the autoclave

For vapor-phase drying in the autoclave, you must open the kerosene drain
plug in the oil compartment base before drying so that the kerosene conden-
sate can drain from the oil compartment.
1.

NOTICE!

Unscrew kerosene drain plug between oil compartment base

and selector gear clockwise until it starts to get hard to turn.Never un-
screw the kerosene drain plug all the way.

Figure 128: Kerosene drain plug

2.

NOTICE!

Remove the on-load tap-changer head cover (24 screws M10/

wrench size 17 with safety elements) and store it outside the auto-
clave.If this is not done, the on-load tap-changer head cover may be
damaged.

3.

NOTICE!

Remove on-load tap-changer accessories (motor-drive unit,

drive shaft, protective relay, pressure monitoring device, pressure relief
device, bevel gear, temperature sensor, oil filter unit) and store outside
autoclave. If this is not done, the on-load tap-changer accessories may
be damaged.

Vapor-phase drying in the autoclave

1.

Supply kerosene vapor at a temperature of around 90 °C. Keep this
temperature constant for 3 to 4 hours.

2.

Increase the kerosene vapor temperature by approx. 10 °C/hour to the
desired final temperature (125 °C maximum on the on-load tap-chang-
er).

3.

Vacuum dry on-load tap-changer at between 105 °C and maximum 125
°C for at least 50 hours.

4.

Residual pressure of no more than 10

-3

bar.

NOTICE!

Close kerosene drain plug (tightening torque 20 Nm). An open

kerosene drain plug leads to oil escaping from the oil compartment and
therefore to damage to the on-load tap-changer and transformer.

6.6.2

«
...
112
113
114
115
116
...
»

Содержание VACUTAP VR













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: FJC Страницы: 2

Бренд: UFO Страницы: 16

Бренд: Baileigh Industrial Страницы: 40

Бренд: Kawai Страницы: 10

Бренд: Parker Research Corp Страницы: 4

Бренд: Eastwood Страницы: 20

Бренд: Daihan Scientific Страницы: 43

Бренд: York Fitness Страницы: 20

Бренд: GE Страницы: 241

Бренд: GE Страницы: 223

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Бренд: Reflex Marine Страницы: 36

Thermo Therapy TT-202

Бренд: Whitehall Страницы: 12

Бренд: Ocean Guardian Страницы: 41

Бренд: Com-Power Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды