MR VACUTAP VR Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 268

background image

6 Assembly: Bell-type tank design

Maschinenfabrik Reinhausen GmbH 2015

113

4349315/00 EN

VACUTAP® VR®

Without interruption
in measured current

With interruption
(measured current = 0
A before change in
operating position)

Oil compartment filled
with insulating oil

Maximum 50 A DC

Maximum 50 A DC

Table 8: Maximum permitted measured currents when measuring DC resistance on
transformer

Drying on-load tap-changer in autoclave

Dry on-load tap-changer using the following instructions to ensure the dielec-
tric values assured by MR on the on-load tap-changer.

If you want to dry the on-load tap-changer in an autoclave, first perform the
drying process and then complete transformer assembly.

If drying in an autoclave, the following methods are possible:
▪

Vacuum-drying

▪

Vapor-phase drying

Vacuum-drying in the autoclave

Before starting vacuum-drying in the autoclave, you must remove the on-
load tap-changer head cover and on-load tap-changer accessories:
1.

NOTICE!

Remove the on-load tap-changer head cover (24 screws M10/

wrench size 17 with safety elements) and store it outside the autoclave.
If this is not done, the on-load tap-changer head cover may be dam-
aged.

2.

NOTICE!

Remove on-load tap-changer accessories and store outside

autoclave: motor-drive unit, drive shaft, protective relay, pressure moni-
toring device, pressure relief device, bevel gear, temperature sensor, oil
filter unit. If this is not done, the on-load tap-changer accessories may
be damaged.

Vacuum-drying in the autoclave

1.

Heat up the on-load tap-changer in air at atmospheric pressure with a
temperature increase of about 10 °C/h to a final temperature of maxi-
mum 110 °C.

2.

Pre-dry the on-load tap-changer in circulating air at a max. temperature
of 110 °C for a period of 20 hours.

3.

Vacuum dry on-load tap-changer at between 105 °C and maximum 125
°C for at least 50 hours.

4.

Residual pressure of no more than 10

-3

bar.

6.6

6.6.1

«
...
111
112
113
114
115
...
»

Содержание VACUTAP VR













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR

Бренд: Makerfire Страницы: 10

Бренд: IEMCA Страницы: 82

KID 80-IV Touch

Бренд: IEMCA Страницы: 122

Бренд: Calrec Страницы: 92

Бренд: Park House Healthcare Страницы: 12

Бренд: Milestone Страницы: 64

Бренд: Ocean Guardian Страницы: 41

Бренд: Com-Power Страницы: 10

Бренд: Fri-Jado Страницы: 48

Бренд: Janschitz Страницы: 40

Бренд: Dangerous power Страницы: 38

Бренд: Channel Master Страницы: 7

Бренд: ALLSPEEDS Страницы: 22

LFC500-FS Series

Бренд: Watts Страницы: 8

Bowflex SelectTech Stand

Бренд: Nautilus Страницы: 8

Бренд: Megger Страницы: 24

Бренд: Mackie Страницы: 56

Бренд: Bihong Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды