Mitsubishi Electric FR-D700 Series, Инструкция по эксплуатации

Страница: 63 / 290

Parameter list Parameter list
52
4
P
A
RAMETE
R
S
Parameter List
4.2 Parameter list
4.2.1 Parameter list
For simple variable-speed operation of the inverter, the initial setting of the parameters may be used as they are. Set the
necessary parameters to meet the load and operational specifications. Parameter setting, change and check can be made
from the operation panel. For details of parameters, refer to the instruction manual.
These instruction codes are used for parameter read and write by using Mitsubishi inverter protocol with the RS-485 communication.
(
Refer to page 204
for RS-485 communication)
" " indicates valid and "
×
" indicates invalid of "control mode-based correspondence table", "parameter copy", "parameter clear", and "all parameter clear".
Func-
tion
Parameter Name Setting Range
Minimum
Setting
Increments
Initial
Value
Refer
to
Page
Customer
Setting
Parameter Remarks
Instruction Code
Control Mode-based
Correspondence Table
Parameter
Read Write Extended Copy Clear All clear
Basic functions
0 Torque boost 0 to 30% 0.1% 6/4/3%
∗1
69 0 00 80 0
×
1 Maximum frequency 0 to 120Hz 0.01Hz 120Hz
78
1 01 81 0
2 Minimum frequency 0 to 120Hz 0.01Hz 0Hz 78 2 02 82 0
3 Base frequency 0 to 400Hz 0.01Hz 50Hz 80 3 03 83 0
×
4 Multi-speed setting (high speed) 0 to 400Hz 0.01Hz 50Hz 84 4 04 84 0
5 Multi-speed setting (middle speed) 0 to 400Hz 0.01Hz 30Hz 84 5 05 85 0
6 Multi-speed setting (low speed) 0 to 400Hz 0.01Hz 10Hz
84
6 06 86 0
7 Acceleration time 0 to 3600s 0.1s 5/10s
∗2
91 7 07 87 0
8 Deceleration time 0 to 3600s 0.1s 5/10s
∗2
91 8 08 88 0
9 Electronic thermal O/L relay 0 to 500A 0.01A
Rated
inverter
current
95 9 09 89 0
D
C
inj
ec
tio
n
bra
ke
10 DC injection brake operation frequency 0 to 120Hz 0.01Hz 3Hz
104
10 0A 8A 0
11 DC injection brake operation time 0 to 10s 0.1s 0.5s 104 11 0B 8B 0
12 DC injection brake operation voltage 0 to 30% 0.1% 6/4%
∗3
104 12 0C 8C 0
— 13 Starting frequency 0 to 60Hz 0.01Hz 0.5Hz 93 13 0D 8D 0
— 14 Load pattern selection 0 to 3 1 0 82 14 0E 8E 0
×
JO
G
opera
tion
15 Jog frequency 0 to 400Hz 0.01Hz 5Hz 86 15 0F 8F 0
16 Jog acceleration/deceleration time 0 to 3600s 0.1s 0.5s 86 16 10 90 0
— 17 MRS input selection 0, 2, 4 1 0 110 17 11 91 0
— 18 High speed maximum frequency 120 to 400Hz 0.01Hz 120Hz
78
18 12 92 0
— 19 Base frequency voltage 0 to 1000V, 8888, 9999 0.1V 8888 80 19 13 93 0
×
Accel
erati
on/
deceleration time
20
Acceleration/deceleration reference
frequency
1 to 400Hz 0.01Hz 50Hz
91
20 14 94 0
St
al
l
pr
evention
22 Stall prevention operation level 0 to 200% 0.1% 150% 74 22 16 96 0
23
Stall prevention operation level
compensation factor at double speed
0 to 200%, 9999 0.1% 9999 74 23 17 97 0
Multi-
sp
eed
setting
24 Multi-speed setting (speed 4) 0 to 400Hz, 9999 0.01Hz 9999
84
24 18 98 0
25 Multi-speed setting (speed 5) 0 to 400Hz, 9999 0.01Hz 9999 84 25 19 99 0
26 Multi-speed setting (speed 6) 0 to 400Hz, 9999 0.01Hz 9999 84 26 1A 9A 0
27 Multi-speed setting (speed 7) 0 to 400Hz, 9999 0.01Hz 9999 84 27 1B 9B 0
— 29
Acceleration/deceleration pattern
selection
0, 1, 2 1 0 94 29 1D 9D 0
REMARKS
indicates simple mode parameters.
The parameters surrounded by a black border in the table allow its setting to be changed during operation even if "0" (initial
value) is set in
Pr. 77 Parameter write selection .
V/F V/F V/F GP MFVC GP MFVC GP MFVC