Mercury 225 EFI Скачать руководство пользователя | Manualshive

Страница: 670 / 719

background image

ATTACHMENTS / CONTROL LINKAGE

90-884294 OCTOBER 2001

Page 7-3

NOTE: Ride-Guide Steering Cables are lubricated at the factory and require no additional
lubrication at initial installation.

WARNING

Core of each steering cable (transom end) must be fully retracted into cable hous-
ing before lubricating cable. If cable is lubricated while extended, hydraulic lock
of cable could occur.

3. With core of Ride-Guide Steering Cable (transom end) fully retracted, lubricate transom

end of steering cables through grease fittings (a) with 2-4-C Marine Lubricant with Te-
flon. Lubricate exposed portion of cable end (b) with 2-4-C Marine Lubricant with Teflon.

4. Lubricate pivot point (c) of steering link rod and ball joint (d) of link rod with SAE 30

Weight Oil (obtain locally).

5. Inspection and lubrication of steering head assembly (rotary or straight rack) should

be performed once each year (by your Authorized Dealer) or whenever steering
mount and/or steering head are disassembled, or if steering effort has increased. Lu-
bricate with 2-4-C Marine Lubricant with Teflon.

d

c

b

a

a

57834

Ride Guide Steering Cable/Attaching Kit Installation
(92876A8)

Dual Cable - Single Outboard

WARNING

Quicksilver Super Ride-Guide Steering (dual cables) MUST BE USED with this at-
taching kit. Failure to adhere to this requirement could result in steering system
failure.

Refer to “Quicksilver Accessories Guide” to determine correct length of steering
cables and remote control cables.

IMPORTANT: Steering cables and remote control cables MUST BE THE CORRECT
LENGTH, sharp bends on too-short cables result in “kinks”; too-long cables re-
quire unnecessary bends and/or loops. Both conditions place extra stress on the
cables and will reduce the performance of the steering system.

CAUTION

With this kit installed, the upper (outboard) mounting bolts MUST BE installed so
that hex head end of bolts is on the inside of boat transom, as illustrated. Failure
to install upper mounting bolts, as shown in illustration, could result in interfer-
ence between steering cable nut and ends of mounting bolts when outboard is
tilted up.

«
...
668
669
670
671
672
...
»

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

Бренд: Admiral Страницы: 9

Бренд: Vanguard Страницы: 124

Бренд: Lenze Страницы: 20

Бренд: Nissei Страницы: 16

Бренд: Perkins Страницы: 27

Бренд: Toyama Страницы: 44

Бренд: DLE Страницы: 4

Бренд: MTU Страницы: 187

Low Voltage Motors EQPIII-841

Бренд: Toshiba Страницы: 2

Low Voltage Motors VR Series

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 18

Бренд: Toshiba Страницы: 31

Бренд: Toshiba Страницы: 49

Бренд: YS Страницы: 2

Бренд: Stober Страницы: 34

Бренд: O.S. engine Страницы: 18

Бренд: JaxSon Страницы: 40

Бренд: Mitsubishi Heavy Industries Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды