Mercury 225 EFI Скачать руководство пользователя | Manualshive

Страница: 242 / 719

background image

FUEL INJECTION

90-884294

Page 3B-13

OCTOBER 2001

CAUTION

Wipe up fuel spills immediately.

CAUTION

Depressurize fuel system prior to opening line connections or removing fuel sys-
tem components.

DANGER

Perform the tests in this section in a well ventilated area to avoid being overcome
by fuel vapors or poisonous exhaust gases.

Fuel Injection System Function

Fuel is delivered directly to the engine by way of fuel injectors. These injectors are provided
with a constant supply of fuel (41 to 45 psi; 283 to 310 kPa) delivered to the fuel rail. The
injectors are opened and closed electronically by the Electronic Control Module (ECM).
The ECM receives input signals from various sensors in the EFI system which in turn trans-
mits controlling outputs (open/close) to the injectors. The length of time the injectors stay
open is considered pulse width. The pulse width will widen (richer) or narrow (leaner) de-
pending on signals ECM receives from sensors, to allow efficient operation at all speeds
and conditions.

IMPORTANT: The following preliminary steps MUST BE FOLLOWED before at-
tempting EFI problem diagnosis.

Preliminary Checks

Ignition Spark Check

Purpose: This test determines if the ignition system is delivering usable spark to the spark plugs. By perform-

ing this test, the probable cause can be isolated to either the ignition system or fuel system.

1. Disconnect all spark plug wires from spark plugs.

2. Connect Spark Gap Tester (91-850439T1) to a good ground on engine. Connect Spark

Plug Extensions (91-877870A1) between tester and spark plug leads.

3. Connect Remote Starter Switch (91-52024A1) to starter solenoid.

a. Connect RED lead from switch to large positive (+) terminal with RED banded

cable attached [(+) cable from battery].

b. Connect BLACK lead from switch to small terminal with YELLOW/RED lead at-

tached.

4. Turn ignition key switch to the “ON” position.

OFF

ON

START

5. Look at spark gap tester viewing port for presence of good quality spark.

A steady, blue spark should be present at each spark plug wire. If a good spark is present,
problem may not be ignition related. If good spark is not present, problem may be ignition
related. Troubleshoot ignition system. Refer to appropriate ignition section in this service
manual.

«
...
240
241
242
243
244
...
»

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

Бренд: O.S. engine Страницы: 21

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Бренд: Mercedes-Benz Страницы: 940

Бренд: Saito Страницы: 8

Sonesse Ultra 50 DC RS485

Бренд: SOMFY Страницы: 16

Бренд: Jenny Science Страницы: 9

Бренд: VDG Страницы: 18

Бренд: King Canada Страницы: 8

Бренд: Man Страницы: 42

Бренд: Man Страницы: 48

Бренд: Motorola Страницы: 82

Бренд: Magnetic Страницы: 24

Бренд: Baumuller Страницы: 22

Бренд: Motion Страницы: 52

Бренд: Motion Страницы: 64

Бренд: Yanmar Страницы: 20

Бренд: Yanmar Страницы: 50

Бренд: Yanmar Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды