Mercury 225 EFI Скачать руководство пользователя | Manualshive

Страница: 268 / 719

background image

FUEL INJECTION

90-884294

Page 3B-39

OCTOBER 2001

Condition

Possible Source

Action

Engine Idles Rough (May Lean
Sneeze) – Acceleration OK; Full
Throttle Ok. (continued)

– Ignition Coil Failure.

– Broken Reed.

Refer to Section 2A Electrical
and Ignition Tests.

Inspect Reed Assembly

Engine Runs but Slowly Drops
RPM then Dies.

– Restrictions in Fuel System

between Tank and Engine.

– Clogged Final Filter.

– Pulse Fuel Pump Failure.

– Electric Fuel Pump Delivery

Failure.

Install remote gas tank with
fresh, high quality fuel.

Perform Final Filter Check.

Follow Low Pressure Fuel Route
Flow Chart.

Follow High Pressure Fuel Route
Flow Chart.

Engine Stops for No Apparent
Reason or Does Not Start.

– Battery Undercharged.

– EFI Harness Connections.

– Ignition System Failure.

– Pulse Fuel Pump Failure.

– Electric Fuel Pump Failure.

– ECM Failure.

Check battery connections, un-
der charged battery or worn out
battery.

Check EFI harness connector for
improper connection.

Refer to Section 2A Electrical
and Ignition Tests.

Follow Low Pressure Fuel Route
Flow Chart.

Follow High Pressure Fuel Route
Flow Chart.

The DDT (91-823686T2) will
monitor information coming from
sensors or switches to the ECM
and will indicate if the sensor or
switch is defective. For a more
thorough analysis of the ECM,
refer to EFI Tester Manual
91-11001A2.

Engine Stops for No Apparent
Reason, but will Restart.

– Restriction in Fuel System

Check fuel pressure on fuel rail
at the RPM that failure occurs.

*R.F.I. Radio Frequency Interference. High voltage can alter signals ECM receives from sensors causing im-
proper fuel delivery. Route all sensor wires away from high voltage leads (i.e. spark plug leads)

«
...
266
267
268
269
270
...
»

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

Бренд: RCGF Страницы: 22

Бренд: Eaton Страницы: 16

Бренд: Motor Power Company Страницы: 59

Бренд: Baratza Страницы: 5

MaxxForce DT 10

Бренд: Navistar Страницы: 109

Бренд: WEICHAI Страницы: 33

Бренд: WEG Страницы: 68

Бренд: YS Страницы: 5

DYNAMIC LINE III

Бренд: KEB Страницы: 60

Бренд: WÜRGES Страницы: 24

Бренд: Hacker Страницы: 2

Бренд: Hacker Страницы: 7

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Yanmar Страницы: 214

Бренд: Fanotec Страницы: 2

Бренд: Seva-tec Страницы: 20

Бренд: DANA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды