Mercury 225 EFI Скачать руководство пользователя

Страница: 633 / 719

LEFT HAND NON-RATCHETING

90-884294 OCTOBER 2001

Page 6B-69

UPPER DRIVESHAFT BEARING CLEARANCE

1. When the correct pinion gear height is achieved, remove pinion nut, upper retainer

and driveshaft.

2. Apply Premium Gear Lubricant to O.D. of the driveshaft lower bearing cup and install

cup into the gear case.

3. Reinstall driveshaft and pinion gear into gear case.

4. Install the upper drive shaft bearing cup and install and torque the upper bearing re-

tainer to 100 lb. ft. (135 Nm).

5. Torque pinion nut to 70 lb. ft. (95 Nm).

57935

a -

Bearing Retainer Tool (91-43506)

6. Push down on drive shaft and check clearance between pinion gear and pinion gear

shimming tool shoulder. Clearance should be 0.020 in - 0.024 in. (0.51 mm - 0.61 mm).

a -

Pinion Gear Shimming Tool (91-12349A2) Using Disc #2 and Flat #4

b -

Feeler Gauge

NOTE: Do not change shims under upper bearing cup or pinion height will be changed.

7. Maintain the shims as previously set under the upper drive shaft bearing cup.

8. If clearance is not within specifications, remove the upper bearing cup retainer with

tool 91-43506 and remove cup. Leave upper cup shim(s) in place.

NOTE: A 0.001 in. (25.4 mm) change of shims under the lower bearing cup will result in
a 0.001 in. (25.4 mm) change in drive shaft end play.

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды

Mercury 225 EFI, Руководство по обслуживанию

Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды