Mercury 225 EFI Скачать руководство пользователя

Страница: 250 / 719

FUEL INJECTION

90-884294

Page 3B-21

OCTOBER 2001

Fuel Rail Electrical/Fuel Determination

•

Perform all preliminary checks page 3B-13.

•

Adequate fuel pressure (41 to 45 psi; 283 to
310 kPa) follow Low/High Fuel Route Flow
Charts.

•

Run engine @ idle and with DDT, perform
cylinder load test.

No RPM change on cylinder(s),
indicating problem in cylinder(s).

RPM decreases (on each cylinder).

Perform Fuel Injector load test.

Fuel delivery OK.

Defective injector or broken cir-

cuit to injector.

Perform Induction Manifold
Disassembly and inspection.

Perform compression check on
problem cylinder.

Low or no compression on cylinder.

Compression OK.

Inspect cylinder bore. Refer to
Section 4 for disassembly.

NOTE: Injector filters must be
inspected prior to reassembly.

Check:
1) Damaged reeds
2) End cap seals
3) Crankcase split line leak
4) Crankshaft sealing rings

Results

Fuel Injector has audible click.

Results

Injector is functioning properly

Results

Fuel Injector does not have audible click.

Perform Ignition Coil load test.

Ignition spark OK

Weak or no ignition spark

Replace defective coil, spark plug
or wiring

Results

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды

Mercury 225 EFI, Руководство по обслуживанию

Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды