manualshive.com logo in svg

Mercury 225 EFI, Руководство по обслуживанию

Меркурий 225 EFI - великолепный мотор для лодки, обеспечивающий отличную мощность и производительность. Для обслуживания и ремонта необходимо скачать бесплатный сервисный мануал на manualshive.com. Этот руководство поможет вам ухаживать за вашим мотором и поддерживать его в отличном состоянии.

Поделиться
Скачать
background image

POWERHEAD

Page 4A-64

90-884294   OCTOBER 2001

4. Check piston rings to be sure that they fit freely in ring groove.

5. Lubricate piston, rings and cylinder wall with 2-Cycle Outboard Oil.

52319

a

b

   

a -

Piston Ring Expander (91-24697)

   

b -

Dot Side “Up” on Piston Ring

6. Rotate each piston ring so end of ring is aligned with locating pin as shown.

7. Install Piston Ring Compressor.

8. Remove screws and connecting rod cap from piston rod assembly being installed.

IMPORTANT: Piston must be correctly installed and positioned as shown.

Pistons marked with the word “UP” and with the letter “P” or “S” on top of piston.

Pistons with the letter “P” must be installed in the port side of engine and the word “UP” fac-
ing toward top of engine.

Pistons with the letter “S” must be installed in the starboard side of engine and the word “UP”
toward top of engine.

9. Coat cylinder bore with 2-cycle oil. Match piston assembly with cylinder it was removed

from, and position piston as described below. Push piston into cylinder.

CYL 2

CYL 4

CYL 6

CYL 1

CYL 3

CYL 5

UP

P

UP

P

UP

P

UP

S

UP

S

UP

S

14

2 Cycle Outboard Oil

52328

14

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

GAS GAS EC 200 Workshop Manual preview
EC 200
Бренд: GAS GAS Страницы: 71
ZF ZF 25 A Operating Instructions Manual preview
ZF 25 A
Бренд: ZF Страницы: 80
CIMCO OXE Series Manual preview
OXE Series
Бренд: CIMCO Страницы: 24
TEKCELEO WLG-30-R Getting Started preview
WLG-30-R
Бренд: TEKCELEO Страницы: 6
Baldor Reliance CDX7150 Installation & Operating Manual preview
Reliance CDX7150
Бренд: Baldor Страницы: 32
Nederman 920/1500 Installation And Service Manual preview
920/1500
Бренд: Nederman Страницы: 44
DJ ENGINE DJ72-GTS User Manual preview
DJ72-GTS
Бренд: DJ ENGINE Страницы: 9
Johnson Electric Nanomotion SE Series User Manual preview
Nanomotion SE Series
Бренд: Johnson Electric Страницы: 33
Canaline Engines Canaline 25 Operator'S Handbook Manual preview
Canaline 25
Бренд: Canaline Engines Страницы: 39
TEM 50-400 V CA Series Operation And Maintenance Manual preview
50-400 V CA Series
Бренд: TEM Страницы: 44
YS DZ170CDI Operator'S Manual preview
DZ170CDI
Бренд: YS Страницы: 2
Robin America Engine EX40 Parts Manual preview
Engine EX40
Бренд: Robin America Страницы: 32
Robin America EH72 Instructions For Use Manual preview
EH72
Бренд: Robin America Страницы: 35
Volvo Penta V8-225 Operator'S Manual preview
V8-225
Бренд: Volvo Penta Страницы: 116
YASKAWA SGDH User Manual preview
SGDH
Бренд: YASKAWA Страницы: 616
BAFANG MM G510.750.C Manual preview
MM G510.750.C
Бренд: BAFANG Страницы: 12
UMS 5-55 cc User Manual preview
5-55 cc
Бренд: UMS Страницы: 16
PASCO TD-8592 Instruction Manual preview
TD-8592
Бренд: PASCO Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды