manualshive.com logo in svg

Mercury 225 EFI, Руководство по обслуживанию

Меркурий 225 EFI - великолепный мотор для лодки, обеспечивающий отличную мощность и производительность. Для обслуживания и ремонта необходимо скачать бесплатный сервисный мануал на manualshive.com. Этот руководство поможет вам ухаживать за вашим мотором и поддерживать его в отличном состоянии.

Поделиться
Скачать
background image

WIRING DIAGRAMS

Page 2D-58

90-884294   OCTOBER 2001

NOTE: If you are in a stranded situation, stopping the engine and allowing it to cool back
down will usually allow some additional low speed (idle) running time before the engine
starts to overheat again.

The overheat problem must be corrected before you can resume normal operation.

PRESSURE

a

a -

Water Pump Indicator Hole

This alarm message is displayed and the warning horn begins sounding continuously to
inform the driver that there is insufficient water pressure in the cooling system. The Engine
Guardian System will start limiting engine power.

Some causes of insufficient cooling water pressure are (1) obstructed cooling water in-
take holes (2) blockage in the cooling system or a water pump problem (3) running the
outboard with the cooling water intake holes out of the water.

NOTE: The throttle will have to be returned to idle to reset the system.

If the warning system is activated, immediately reduce throttle speed to idle. Shift out-
board into neutral and check for a steady stream of water coming out of the water pump
indicator hole.

If no water is coming out of the water pump indicator hole or flow is intermittent, stop en-
gine and check cooling water intake holes for obstruction. If no obstruction is found, this
may indicate a blockage in the cooling system or a water pump problem. Stop engine.
Operating the engine without adequate cooling water pressure will overheat the engine.

If the warning signals stop and a steady stream of water is coming out of the water pump
indicator hole, return engine to normal operation.

OVERSPEED (a)

This message is displayed and the warning horn begins sounding continuously to inform the
driver that the engine speed has exceeded the maximum allowable RPM. The system will
automatically reduce the engine speed to within the allowable limit.

NOTE: Your engine speed should never reach the maximum limit to activate the system unless
the propeller is ventilating, an incorrect propeller is being used, or the propeller is faulty.

WATER IN FUEL (b)

This message will appear and the warning horn will begin sounding a series of four beeps
every two minutes when water in the water separating fuel filter reaches the full level. The
water can be removed from the filter.

FAULT-HORN (c)

This message informs you that warning horn is not functioning correctly.

a

b

c

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

YOODA 35EV/S Series Manual preview
35EV/S Series
Бренд: YOODA Страницы: 7
pumpa 4RP201M Translation Of The Original Instruction Manual preview
4RP201M
Бренд: pumpa Страницы: 32
WÄRTSILÄ 12V46F Product Manual preview
12V46F
Бренд: WÄRTSILÄ Страницы: 200
YOODA 35EVY Series Quick Start Manual preview
35EVY Series
Бренд: YOODA Страницы: 7
Zimmer HF150-003 Installation And Operating Instruction preview
HF150-003
Бренд: Zimmer Страницы: 40
Nice Neomat A Series Instructions And Warnings For The Fitter preview
Neomat A Series
Бренд: Nice Страницы: 52
Generac Power Systems 3.0 LITER Service Manual preview
3.0 LITER
Бренд: Generac Power Systems Страницы: 218
MULTIPLEX modell DF69 Instructions Manual preview
DF69
Бренд: MULTIPLEX modell Страницы: 6
WilTec 99200 Operation Manual preview
99200
Бренд: WilTec Страницы: 16
WilTec 92454 Operation Manual preview
92454
Бренд: WilTec Страницы: 26
LinMot P10-70 Installation Manual preview
P10-70
Бренд: LinMot Страницы: 54
LinMot PR01 Series Manual preview
PR01 Series
Бренд: LinMot Страницы: 79
LinMot 0150-4370 Installation Manual preview
0150-4370
Бренд: LinMot Страницы: 47
Royal Enfield EURO IV Service Manual preview
EURO IV
Бренд: Royal Enfield Страницы: 152
LinMot P01-37S-HP-SSCP Installation Manual preview
P01-37S-HP-SSCP
Бренд: LinMot Страницы: 28
Sauer Danfoss OMS Series 3 Repair Instructions preview
OMS Series 3
Бренд: Sauer Danfoss Страницы: 16
Mitsubishi 6M70 Workshop Manual preview
6M70
Бренд: Mitsubishi Страницы: 364
A'OK AM60 ESSENTIAL M Instructions For Use Manual preview
AM60 ESSENTIAL M
Бренд: A'OK Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды