manualshive.com logo in svg

Mercury 225 EFI, Руководство по обслуживанию

Меркурий 225 EFI - великолепный мотор для лодки, обеспечивающий отличную мощность и производительность. Для обслуживания и ремонта необходимо скачать бесплатный сервисный мануал на manualshive.com. Этот руководство поможет вам ухаживать за вашим мотором и поддерживать его в отличном состоянии.

Поделиться
Скачать
background image

ATTACHMENTS / CONTROL LINKAGE

Page 7-24

90-884294   OCTOBER 2001

STEERING SYSTEM TENSION ADJUSTMENT (PARALLEL ROUTED STEERING CABLES)

IMPORTANT: For proper operation of this dual cable - dual outboard steering instal-
lation, there MUST BE proper tension in the steering system. NOT ENOUGH ten-
sion will cause slack (play) in steering system. TOO MUCH tension will cause steer-
ing cables to bind. Perform the following steps to correctly adjust tension.

Loosen adjustment nuts and pull steering cable mounting tube (by hand) away from end
of steering cable (to remove slack in steering system). Tighten adjustment nuts against
mounting bracket and check system for slack (play). If steering system is too tight, read-
just tube toward end of steering cable or, if too much slack (play) exists in system, readjust
tube away from end of steering cable. Tighten nuts against mounting bracket and read-
just, if necessary.

51887

a

b

c

d

a -

Steering Cable Mounting Tube

b -

Adjustment Nuts

c -

Adjust Tube in This Direction to Remove Slack from Steering System

d -

Adjust Tube in This Direction to Reduce Tension from Steering System

After steering system tension is adjusted correctly, tighten adjustment nuts against
mounting bracket to a torque of 35 Ib. ft. (47.5 Nm) and bend a tab lock washer against
a flat on each nut.

51887

c

c

a

b

a -

Steering Cable Mounting Tube

b -

Adjustment Nuts; Torque to 35 lb. ft. (47.5 Nm)

c -

Tab Lock Washer (Bend Against Flat on Each Adjustment Nut)

Tighten steering cable attaching nuts of each steering cable to a torque of 35 Ib. ft.
(47.5 Nm).

NOTE: Cable attaching nuts with a “V” groove around outer circumference are self locking
and do not require locking sleeves.

WARNING

After installation is complete [and before operating outboard(s)], check that boat
will turn right when steering wheel is turned right and that boat will turn left when
steering wheel is turned left. Check steering thru full range (left and right) at all
tilt angles to assure interference-free movement.

Adjust trim tabs of both outboards, as outlined in “Trim Tab Adjustment,” following.

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

RHINO MOTION CONTROLS RMCS-2302 Installation Manual And Datasheet preview
RMCS-2302
Бренд: RHINO MOTION CONTROLS Страницы: 4
Weber MPE 750 Turbo Service Manual preview
MPE 750 Turbo
Бренд: Weber Страницы: 35
APRILIA Air-injection 50 cc Quick Workshop Handbook preview
Air-injection 50 cc
Бренд: APRILIA Страницы: 33
TIS TIS-TM120 Installation Manual preview
TIS-TM120
Бренд: TIS Страницы: 12
ETQ 170F Owner'S Manual preview
170F
Бренд: ETQ Страницы: 89
Crestron QMT 5 Series Installation Manual preview
QMT 5 Series
Бренд: Crestron Страницы: 2
Baumr-AG E42 User Manual preview
E42
Бренд: Baumr-AG Страницы: 25
Fagor SPM Manual preview
SPM
Бренд: Fagor Страницы: 86
V.P.S. 160F Owner'S Manual preview
160F
Бренд: V.P.S. Страницы: 25
MULTIPLEX modell 33 3060 Instructions Manual preview
33 3060
Бренд: MULTIPLEX modell Страницы: 11
ZIEHL-ABEGG ZA top SM225.40B Original Operating Instructions preview
ZA top SM225.40B
Бренд: ZIEHL-ABEGG Страницы: 76
Honda GSV190 Owner'S Manual preview
GSV190
Бренд: Honda Страницы: 16
Honda GS190 Owner'S Manual preview
GS190
Бренд: Honda Страницы: 16
Stiga TM 60 Operator'S Manual preview
TM 60
Бренд: Stiga Страницы: 40
STEYR MO114K33 Operation, Maintenance And Warranty Manual preview
MO114K33
Бренд: STEYR Страницы: 118
KEM KODIAK MARINE LT4 SUPERCHARGED Operator'S Manual preview
KODIAK MARINE LT4 SUPERCHARGED
Бренд: KEM Страницы: 66
Mitsubishi Heavy Industries GT 1000 Owner'S Manual preview
GT 1000
Бренд: Mitsubishi Heavy Industries Страницы: 32
Desert Aircraft DA-100L Owner'S Manual preview
DA-100L
Бренд: Desert Aircraft Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды